R0015046 Bench Assemble Infeed Clamps

Instructions to bench assemble infeed clamp assembly

Difficulté

Medium Moyen

Durée

2 hour(s) heure(s)

R0015046_Bench_Assemble_Infeed_Clamps_Screenshot_2023-07-19_121320.png

Introduction

Tools Required

Standard hex key set

Standard spanner set

External circlip pliers

Grease for lubrication M0000494

Parts Required

B0000062 Circlip 20mm External x 2

B0000070 Linear Bearing: Ø25 x 40 Compact (Metal Case Only) x 8

B0001176 Washer :bearing shim x 3

D0000209 Shaft Strap (D8709) x 1

D0000211 Cylinder Extension x 1

D0001331 Roller Ø40 x 27 c/w bearing x 3

D0001334 Roller Ø40 x 102 c/w bearing x 2

D0003108 Shaft 20mm: 146mm Clamp Roller Shaft x 2

D0003788 Z Roller Pin (40mm) x 3

D0007680 Infeed Rail x 1

D0007774 Top Roller Block x 1

D0007792 Z Roller Block (D8711) x 1

D0007793 Z Roller Plate (D8710) x 1

D0015427 MC Hold Clamp Bar x 1

D0015428 Top Clamp Block Ø30 15 x 1

H0007773 Shaft 25mm: 268mm ZX Infeed Clamp Top x 2

H0007791 Shaft 25mm :250mm ZX Infeed side x 2

P0000007 Straight Adaptor 6mm - 1/8 BSP tapered thread x 1

P0000200 Elbow Adaptor 6mm - M5 x 2

P0000484 Cylinder 32 x 100 stroke x 1

P0001160 Cylinder 32 x 70 stroke x 1

P0001198 Fitting: flow control 1/8 x 6mm elbow x 4

Étape 1 - Unless otherwise stated

Use locktite 243 on all fasteners

Use loctite 572 on all threaded pneumatic connection

Pen mark all fasteners to show finalised

Étape 2 - Fit bearings to main blocks

Fit 8 off B0000070 bearings to D0007680 Infeed Rail and D0007792 Z Roller Block (D8711) as shown

Ensure yellow part of bearing is always facing outside edge when fitted

Thoroughly grease bearings with M0000494 lubricant once fitted, ensuring all ball chambers are filled with grease

Étape 3 - Check fitment of the following rollers

1 D0001331 Roller Ø40 x 27 c/w bearing and D0003788 Z Roller Pin (40mm)

2 D0001334 Roller Ø40 x 102 c/w bearing and D0003108 Shaft 20mm: 146mm Clamp Roller Shaft

Étape 4 - Check fit of shafts in bearings

Check fit of following parts .

Shafts should pass through bearings with only slight resistance . All inner bearing faces should have contact to shaft and rotate when the shaft is turned

If shafts are tight check drawing and inspect size of shaft .

If shaft slides through easily, then follow step 4

Étape 5 - Degrease and bearing fit

.....only follow this step is bearing/shaft fit is loose. Use these generic steps for assembly of issued rollers

Thoroughly degrease all parts with FE10 solvent

1 Fit 20mm external circlip to shaft

2 Fit roller to shaft

3 Add 3 drops of Loctite 641 bearing retainer to indicated area and smear around the shaft

4 Move shaft to shown position and add 3 more drops of bearing fit to indicated face and smear around

5 Position roller against circlip and remove any excess bearing fit with rag

6 Leave roller in a vertical position to allow bearing fit to cure

Étape 6 - Fit shafts

Fit H0007791 Shaft 25mm :250mm ZX Infeed side x 2 as shown .

Use 2 off M8 x 12 K.C.P grubscrew to secure

Étape 7 - Fit z block

Slide on D0007792 Z Roller Block taken care not to damage bearing seals

Étape 8 - Attach cylinder

1 Attach 2 off P0001198 Fitting: flow control 1/8 x 6mm elbow to cylinder P0000484 Cylinder 32 x 100 stroke

2 Attach cylinder to assembly using M6 x 35 socket caps and M6 A form washers (do not tension yet )

Find in cylinder piston to leave 2 threads exposed when lock nut is tightened

3 Push cylinder assembly to closed position (shown) and apply tension to M6 fixings

Finalise all bolts and nuts

4 Check alignment . Cylinder stroke should be even and smooth at all points of travel . There should be no tight spots, especially at the end points of cylinder travel

Étape 9 - Fit z roller plate

Use 4 off M6 x 16 socket caps and A form washers to fit D0007793 Z Roller Plate

...Ensure recess is positioned correctly against indicated face

Étape 10 - Mount low rollers

Attach 3 off low rollers to z plate with M6 x 16 socket counter sunk fasteners

Étape 11 - Assemble top roller Block

en none 0 Draft