R0015278 Mount Completed Assemblies

Instructions to mount completed assemblies to main frame

Difficulté

Medium Moyen

Durée

8 hour(s) heure(s)

R0015278_Mount_Completed_Assemblies_Screenshot_2023-07-14_093443.png

Introduction

Tools Required

Standard Hex key set

Standard spanner set

300 mm rule

1000mm rule

Parts Required

D0008288 Takeup Pad Left (D7339) (Wet/P F Matt) x 1

D0015583 Take Up Beam Joiner x 1

D0015598 Datum Flag: Saw Infeed x 1

D0015717 Energy Chain Angle Bracket Lower x 5

D0015718 Energy Chain Angle Bracket Upper x 2

D0015718B Energy Chain Angle Bracket Double Deck x 3

D0015720 Carriage Bracket x 1

D0015721 Energy Chain Tray Deep Long x 1

D0015723 Energy Chain Tray Shallow x 1

D0015724 Energy Chain Tray Deep x 2

D0015725 Energy Chain Tray Shallow Medium x 1

D0015742 Takeup Pad Right ZX5 x 1

D0015862 Energy Chain Tray Deep Long x 1

E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 1

R0015011 Bench Assemble Gripper

R0015063 Bench Assemble Roller Tables

R0015096 Bench Assemble Transfer Drive Assembly

R0015101 Bench assembly take up assembly

R0015286 Bench Assemble X axis components and energy chain

Étape 1 - Unless otherwise stated

Use loctite 243 on all fasteners

Use Loctite 572 on all threaded pneumatic connections

Pen mark all fasteners to show finalised

Étape 2 - Mount pre built R0015063 Bench Assemble Roller Tables

Mount roller beds as indicated , using M8 x 30 socket caps and heavy M8 washers.

Do not apply adhesive to fasteners and only apply holding tension to fasteners

Étape 3 - Mount pre built R0015011 Bench Assemble Gripper

1 Mount Gripper assembly to carriage using 2 off M8 x 35 socket caps 2 off Mi8 x 2 5 socket caps and heavy M8 washers

2 Check and adjust parallel to ensure gripper is true to hepco beam both indicated measurements should be identical

Étape 4 - Mount Energy chain angle brackets Lower

1 Mount 5 off D0015717 Lower mounting angle with 2 off M10 x 25 set bolts and A form washers per bracket . Do not apply adhesive at this point

2 Set height to just clear plastic frame cap and set bracket level

Étape 5 - Mount upper chain angle brackets

1 Mount 3 off D0015718B to positions shown using M6 x 16 socket caps and heavy M6 washers . Do not apply adhesive to fasteners yet

2 Set slot position to be flush with lower bracket

Étape 6 - Mount short upper chain angle brackets

Mount 2 off D0015718 to indicated point using M6 x 16 socket caps and heavy M6 washers . Set faces flush as with previous step

Do not apply adhesive at this point

Étape 7 - Fit lower chain trays

Lightly fix these parts, as adjustment will be required later

...Do not fit washers under the heads of button heads on all fitted energy chain trays

1 Fit D0015725 at indicated position . Use M5 x 16 button hex bolt, M5 penny washer and M5 nyloc nut .

2 Fit D0015723to indicate point with same fixings as above

3 Fit D0015724 to indicate point with same fixings as above

4 Fit D0015721 to indicate point with same fixings as above

Étape 8 - Mount upper chain guides

Use same method as step 6 to mount indicated upper chain guides 2 off

1 D0015862 upper chain guide

2 D0015724 upper chain guide

Étape 9 - Fit Carriage bracket

..ECR requested to amend bracket with below changes. Rework to shown picture if new style is not issued

Fit D0015720 carriage bracket as shown using M6 x 16 socket caps and A form washers

Étape 10 - Attach pre built R0015286 energy chain

Fit pre built energy chain from assembly R0015286 and attach using M5 x 16 button heads, medium washers and M5 nyloc nuts as shown

...Ensure reversed links are fitted to the gripper assembly connection end Ensure energy chain brackets are fixed so the energy chain runs parallel to the trays

Étape 11 -

en none 0 Draft