WinMulti - IO Screens - Autoflow

This page shows each of the IO Screens on an Autoflow and describes each Input/Output

winMulti, IO, Input, Output

On an Autoflow machining centre there are 3 IO Screens

1. 1. IO
2. 2. IO-Infeed
3. 3. Spindle IO

each of these has a section below with a table describing each input and output.

Autoflow Main IO Screen

Autoflow Main IO Screen

Autoflow Inputs

Module A – Infeed Table

Sensor	Description	Sensor	Description
InA_GripperOff	Gripper Slip Sensor	InA_48vOk	48v Ok (No Errors)
InA_Measure1	Offcut Measure Sensor 1	InA_AirOk	Air Supply OK
InA_Measure2	Offcut Measure Sensor 2	InA_Grip	Gripper Sensor (Profile in place)
InA_GZHome	Gripper Z Axis Home	InA_EStop	Emergency Stop State
InA_GYHome	Gripper Y Axis Home	InA_ButStart	Start Button
InA_GXHome	Gripper X Axis Home	InA_ButStop	Stop Button
InA_MatLoad1	Material Load Sensor 1	InA_ButReset	ES Reset Button
InA_MatLoad2	Material Load Sensor 2	InA_ButEstop1	Emergency Stop Button 1
InA_Index	Infeed Table Index Position	InA_ButEstop2	Emergency Stop Button 2
InA_VCUOk	VCU Ok (No Errors)	InA_ButEstop3	Emergency Stop Button 3
InA_Bus415Ok	Bus415Ok (No Errors)	InA_ButAuto	Auto Load Button
InA_Bus415SOk	Bus415S Ok (No Errors)	InA_MatlAtFence	Material At Back Fence Sensor
InA_24vBusOk	24v Bus Ok (No Errors)	InA_StopOver	Profile Stop
InA_24vModOk	24v Module Ok (No Errors)	InA_ButLoad	Load Button

Module B – Multihead

Sensor	Description	Sensor	Description
InB_YHome	Y Axis Home Switch	InB_ClampOSH	Clamp Outfeed Side Home
InB_ZHome	Z Axis Home Switch	InB_ClampITH	Clamp Infeed Top Home
InB_RHome	R Axis Home Switch	InB_ClampISH	Clamp Infeed Side Home
InB_ClampOTH	Clamp Outfeed Top Home	InB_OilerOK	Oiler OK (No Errors)

Module F – Saw and Outfeed

Sensor	Description	Sensor	Description
InF_SYHome	Saw Y Axis Home (forward/back)	InF_EjectHm	Ejector Home
InF_SZHome	Saw Z Axis Home (up/down)	InF_EjectOu	Ejector Out
InF_SRHome	Saw R Axis Home (rotation)	InF_AdvanceBut	Saw Outfeed Advance Button
InF_EjPushHm	Eject Pusher Home	InF_OutfeedFull	Outfeed Full Sensor
InF_EjPushOu	Eject Pusher Out	InF_OutfeedInd	Saw Outfeed Belt in Position
InF_ClampOTH	Clamp Outfeed Top Home	InF_ClampITPos	Clamp Infeed Platform
InF_ClampOSH	Clamp Outfeed Side Home	InF_TiltHm	Saw Blade Tilt Home (vertical)
InF_ClampITHm	Clamp Infeed Top Home	InF_TiltOu	Saw Blade Tilt Out (tilted)
InF_ClampISHm	Clamp Infeed Side Home	InF_GuardFront	Front Door
InF_RollerITHm	Roller Infeed Top Home	InF_GuardRear	Rear Door
InF_48vOk	48v Ok (no errors)	InF_ServSZOk	Servo Motor Z Axis Ok
InF_24vBusOk	24v Bus Ok (no errors)	InF_ServSROk	Servo Motor R Axis Ok
InF_24vModOk	24v Module Ok (no errors)	InF_ButEstop4	Emergency Stop Button 4

Autoflow Outputs

Module A – Infeed Table

Output	Description	Output	Description
OuA_CtrlOn		OuA_PopUp	Profile Stop Popup
OuA_Grip	Gripper	OuA_StopX	Profile Stop In/Out
OuA_GripBlow	Gripper Blower	BrakesOff	Drive Brakes
OuA_LoadBlow	LoadBlower

Module B – Multihead

Output	Description	Output	Description
OuB_ClampIT	Clamp Infeed Top	OuB_ClampOT	Clamp Outfeed Top
OuB_ClampIS	Clamp Infeed Side	OuB_ClampOTPos	Clamp Outfeed Top Tall Pos
OuB_ClampISPos	Clamp Infeed Side Wide Pos	OuB_ClampOS	Clamp Outfeed Side
		OuB_ClampOSPos	Clamp Outfeed Side Wide Pos

Module F – Saw and Outfeed

Output	Description	Output	Description
OuF_ClampIT	Clamp Infeed Top	OuF_EjectPush	Eject Pusher
OuF_ClampITPos	Clamp Infeed Top Tall Pos	OuF_Conveyor	Outfeed Conveyor
OuF_ClampOT	Clamp Outfeed Top	OuF_Eject	Saw Ejector
OuF_ClampOTPos	Clamp Outfeed Top Tall Pos	OuF_Tilt	Saw Tilt On/Off
OuF_ClampIS	Clamp Infeed Side	OuF_OffBlow	Outfeed Blower
OuF_ClampOS	Clamp Outfeed Side	OuF_Siren	Long Length Siren
OuF_ClampITRoll	Clamp Infeed Rollers	OuF_Gate	Long Length Safety Gate

Autoflow Infeed IO Screen

Autoflow Infeed IO Screen

Autoflow Spindle IO Screen

Autoflow Spindle IO Screen

en none 0

Draft