R0015146 Pneumatic pipe Installation Part 2

Details to install pneumatic and electrical loom

Difficulté

Hard Difficile

Durée

1 minute(s) minute(s)

R0015146_Pneumatic_pipe_Installation_Part_2_Screenshot_2023-12-14_115535.png

Introduction

This instruction is to incorporate assembly R0015033B Module F Wiring loom alongside this

See Electrical department for prepared components from above assembly

Tools Required

Pipe cutters

Pipe identification markers

Flush cutters

Parts Required

P0000010 6mm 1/8 elbow fitting x 6 P0000046 Fitting: 'Y' Adaptor 6mm x 6

P0000047 Bulkhead Elbow 6mm x 1

P0000159 Fitting: Stem Blanking Plug 6mm x 2

P0000160 Fitting: Flow Controller In Line 6mm x 2

P0000551 6mm inline Quick Exhaust Fitting x 3

P0001030 Fitting: SMC 6mm Equal Tee x 1

P0001008 regulator x 3

P0001009 Regulator nut x 3

P0001106 Plug in reducer 12-8mm x 1

P0001107 Fitting 12mm equal tee x 1

P0001166 12mm tube to tube elbow x 1

Étape 1 - Unless otherwise stated

All bolts to have Loctite 243 adhesive applied unless otherwise stated

All Threaded Pneumatic connections to have Loctite 570 applied

All bolts to be pen marked once adhesive applied and correct tension added

Étape 2 - Y82 Outfeed top clamp Y204 Clamp position

1 Ensure clamp assembly is lifted to the highest position

2 Cut 4 off 6mm black air pipes at 5 meters long

3 Route cables through energy chain and box section

4 Exit pipes here , and use air to blow through and identify as 821.829,2041 and 2049

5 Insert loom through cut table hole then wrapped in large spiral wrap

6 Connect cylinders as shown, ensure cylinder shown is fully extended

Étape 3 - Y80 Infeed Top clamp and Y204 Clamp position

1 Ensure Clamp assembly is lifted to highest position and extended out

2 Cut 4 off 6mm black air pipes at 4 meters long

3 Retrieve cable CBX138 from electrical loom box

4 Fit and set position of CBX138 using test box. Switch to read when clamp is at home position (up)

Étape 4 - Y80 Infeed Top clamp and Y204 Clamp position

1 Attach 6mm black pipes as shown

2 Add P0000551 to position shown, and loom pipes and reed switch adding tiewrap to secure to cylinder

3 Loom should enter box section at shown point, no spiral wrap required once entering frame > Keep loom as short as possible in this position

4 Reed switch and pipes will travel separate directions

5 Exit pipes at this point , through cut out

6 Exit reed switch at this point, and join with eject reed switches through exit hole

Étape 5 - Y202 side clamp and Y206 centralise

1 Cut 2 off 6mm black pipes at 2.5 meters identify as 2021 and 2061 and connect as shown , with pipes exiting through cutout

2 Fit 6mm Y connectors and blanks as shown to existing lines 2022 and 2062

3 Connect 2 off 6mm black pipes 2022 and 2062 to cylinders, incorporating P0000551 as shown

4 Loom as shown and connect to 6mm y fittings . Ensure loom is correct length to allow full movement of bottom table but short as possible

Étape 6 - Front Cable Loom

1 Continue loom of pre installed cables EC05F and 24F left flying. Bring into loom cable 41F for front guard and use spiral wrap to run loom as shown . Captivate onto pre installed 1st tie base as shown

Étape 7 - Y207 Saw cut conduit cables

1 Cut 2 off 6mm black airpipes at 5.5 meters and run through saw anaconda

2 Retrieve 01F cable and 15F cable from wiring loom box and run through saw anaconda

Étape 8 - Y207 connection loom

1 use spiral wrap to loom cables and pipes exiting saw anaconda until saw connection box is reached

2 Exit cable 15F from loom (this will terminate into connection box later)

3 Exit cable 01F from loom one wrap later

4 Incorporate reed switch cables into loom (running from cylinder )

5 Continue loom towards cut cylinder

6 Captivate loom with tie wrap onto pre fitted tie base

Étape 9 - Y207 Cylinder connections

1 Connect 1 6mm pipe to nose port of cylinder

2 Connect 1 6mm pipe to base of cylinder, incorporating flow controller

3 Ensure reed switch cables and pipes are loomed exactly as shown due to minimal clearance in operation

4 Once pipes are connected, use air to blow through and identify pipes are add idents accordingly

5 Continue spiral wrap of top loom to point shown , fixing on second tie base

Étape 10 - Fit rear cables

1 Run pre assembled cable 42F from point A to B

2 Run pre assembled cable 5F and 1 off 8mm blue pipe at 7meters long from point A to point C. 5F cable then routes as shown . 8mm blue pipe routes as shown

Étape 11 - Fit rear hood connections

Captivate pre made cables as shown

4F, 42F and 4F

All cables fitted in steps 10 and 11 now can exit lower slot in trunking

Étape 12 - Y213 Blower 1 and 2

1 1 off 6mm black pipe to enter box section as shown

2 Exit at this point

3 Add in line flow control , and identification numbers and attach to blower

4 Add Tee and Y fitting and identification numbers

5 Add additional 6mm pipe to connect blower bulkhead as shown

Étape 13 - Fit small Spiral wrap

1 Fit spiral wrap to Saw blower as shown

2 Fit spiral wrap to cables as shown

Étape 14 - Y210 Z Support and Y213 Blower

en none 0 Draft