R0015334 Fit Centralise Front Table

Fitting and setting details for Sy assembly and centralise top table

Difficulté

Hard Difficile

Durée

2 hour(s) heure(s)

R0015334_Fit_Centralise_Front_Table_Screenshot_2023-10-23_103332.png

Introduction

Tools Required

Standard hex keyset

1 meter straight edge

Large parallels

150mm engineers square

Engineers level 300mm

Parts Required

H0004543 Gap cover saw finger guard

R0000562 Bench assemble centralise top table

R0015037 Bench assemble SY Assembly

Étape 1 - Unless otherwise stated

All bolts to have Loctite 243 adhesive applied unless otherwise stated

All Threaded Pneumatic connections to have Loctite 570 applied

All bolts to be pen marked once adhesive applied and correct tension added

Étape 2 - Add jacking points to frame

Fit 2 off 1/2" x 1" dowels to frame as shown . Ensure dowels are fully seated . Ensure chamfered end of dowel is inserted first

Secure with 2 off M8 x 12 KCP grubscrews

Étape 3 - Mount R0000562 Bench assemble centralise top table

Attach R0000562 Bench assemble centralise top table as shown

Use 4 off M8 x 20 socket caps

Fit assembly at highest position in slots

Dry fit fasteners, apply medium tension

Étape 4 - Add height adjustment points

Add 4 off M8 x 20 KCP grubscrews to points shown .

Adjust grubscrews to touch dowels

Étape 5 - Add squareness adjustment points

Fit 4 off M8 x 12 flat bottomed grubscrews to the points shown

Wind grubscrews to touch frame

Étape 6 - Adjust position

Set initial position of assembly using engineers level on the indicated axis

Use M8 squareness adjusting grubscrews to set position

Set positions level

Étape 7 - Fit finger Guard

Fit H0004543 Gap cover saw finger guard to assembly

finalise fasteners

Étape 8 - Mount R0015037 Bench assemble SY Assembly

Mount R0015037 Bench assemble SY Assembly

Dry fit fasteners

Étape 9 - Adjust square

Use engineers square to check squareness of front rollers to infeed and outfeed cut tables

Use adjusting grubscrews to set square accurately

Étape 10 - Adjust Height of Sy assembly

Set height of Sy assembly to cut tables using jacking grubscrews

Set to gap of 1.5mm -+ 0.5mm

Étape 11 - Quality check

Check once height is adjusted, that Z block operation does not foul cut tables

To do this move both z blocks by hand to active and home position and check contact is not made with the cut tables

Étape 12 - Set Parallel to backfences

Use 1 meter straight edge and additional 2 off large parallels against back roller fence

Add offset shim of 0.002"/0.05mm to driven side

Set front rollers to touch, using M6 socket caps and counter bore clearance to adjust

Report if unable to achieve parallel from this movement

Étape 13 - Recheck Settings

Recheck all settings once final adjustment has been made

Roller squareness to cut tables

Roller height to cut tables

Parallel to back fences

Étape 14 - Finalise Fasteners

Individually remove and apply adhesive to fasteners and apply final tension

Étape 15 - Recheck settings

Recheck all settings once final adjustment has been made

Roller squareness to cut tables

Roller height to cut tables

Parallel to back fences

Étape 16 - Check adjustment grubscrews

Check that no adjustment grubscrews are loose.

Any grubscrews that are not required should still have adhesive applied and lightly tensioned to set in position

en none 0 Draft