R0000558E Bench Assemble Base and Turntable Part 2

bench assembly instructions for main rotary base of saw

Difficulté

Hard Difficile

Durée

0 hour(s) heure(s)

R0000558E_Bench_Assemble_Base_and_Turntable_Part_2_Screenshot_2023-11-03_113949.png

Introduction

Tools Required

Standard hex key set

Standard spanner set

Heat gun

Large Internal Circlip pliers

Standard circlip pliers

8mm hand reamer

Grease gun

Torque wrench

Parts Required

B0000028 Thrust Bearing 140 I/D 180 O/D 31 Long (FAG) x 1

B0000032 Linear Bearing: Ø30 x 50 Compact (Metal Case Only) x 4

B0001087 Angular Contact Bearing 70 I/D 125 O/D 24 Long x 1

B0001088 Circlip 125mm Internal x 1

C0001122K Servo Motor: Beckhoff AM8032-1E10 (Keyed) x 1

C0001179-100 Gearbox NPTO 100-1 x 1

D0004019E Turntable Mk5 (5334E) x 1

D0004033E Alignment Disc Mk5 x 1

D0004147E Turntable Shaft Mk5 x 1

D0004320E Thrust Bearing Housing Mk5 x 1

D0004336 Stay Bar x 2

D0004514E Turntable Base Mk5 x 1

D0004516 Front Bearing Block (5294) x 2

D0010778 Turntable Stop Arm x 1

D0010796 Turntable Housing Cover x 1

H0004631 Shaft 30mm: Base Slide x 2

M0001176 M6 Stainless lock washer x 4

Étape 1 - Unless otherwise stated

All bolts to have Loctite 243 adhesive applied unless otherwise stated

All Threaded Pneumatic connections to have Loctite 570 applied

All bolts to be pen marked once adhesive applied and correct tension added

Étape 2 - Prepare components

1 Use 8mm hand reamer to clean holes indicated in D0004033E Alignment Disc Mk5

2 Attach smaller bearing outer cage to disc using press

3 Use 8mm hand reamer to clean indicated holes on D0004019E Turntable Mk5 (5334E)

Étape 3 - Fit hard stop

1 Fit 2 off 5mm x 28mm dowels to D0010778 Turntable Stop Arm Use Loctite 270 to secure

2 Cut down dowels to 6mm protrusion

3 Fit to flat on turntable pin and secure with 4 off M10 x 50 socket caps

Étape 4 - Fit bearing cage and turntable plate

1 Fit bearing cage from B0000028 Thrust Bearing 140 I/D 180 O/D 31 Long (FAG), Apply more grease then position assembly shown on top and visually align 8mm reamed holes

2 Position D0004019E Turntable Mk5 as shown. Ensure hard stop is in centre position

All 8mm reamed holes should align through the 3 parts. Turntable shaft, alignment disc and turntable

3 Add 2 off m4 x 20 socket caps and tension lightly to indicated holes to fix together

4 Insert 4 off 8mm x 50mm hardened dowels to fix all three parts in correct alignment

5 Remove 2 off previously fitted M4 socket caps, apply adhesive and apply final tension

6 Add 4 off m14 x 60 socket caps and A form washers to finalise fixing of turntable plate

Check rotation once assembled . Movement should be smooooooth and consistent

Étape 5 - Assemble base

1 Fit 4 off B0000032 Linear Bearing: Ø30 x 50 Compact bearings to D0004516 Front Bearing Block (5294) x 2 as shown , ensure bearings are greased after fitting

2 Attach D0004514E Turntable Base Mk5 as shown . Use M6 x 25 and M8 x 25socket caps to fix . Ensure all external faces are flush with bearing blocks

3 Clean 2 off H0004631 Shaft 30mm, Fit 4 off M8 x 40 socket caps and A form washers to indicated holes . Insert through bearing blocks . Ensure dimple in shaft is at the indicated end

4 Fit D0004336 Stay Bar x 2 as shown. Use M8 x 12 kcp grubscrews to locate onto shaft dimple. End of shaft with no dimple, set staybar flush with shaft and tighten grubscrew onto shaft

If the stay bars are a tight fit, these will require polishing with emery tape to remove debris from coating process . Ensure gradually polishing of bores to ensure bores are taken oversize

5 Check and finalised all fixings

Étape 6 - Fit turntable to base

1 Mount Built base as shown, using clamps and spacer blocks

2 Insert built turntable, orientated as shown . Fix with M8 socket caps and A form washers (sizes required)

3 Fit D0010796 Turntable Housing Cover using m4 x 12 button sockets (size required)

Étape 7 - Fit Servo motor

1 Remove key and Degrease thoroughly spindle on C0001122K Servo Motor: Beckhoff AM8032-1E10 (Keyed)

2 Insert motor into gearbox and orientated servo plug as indicated

Affix motor to gearbox using M5 socket caps (size required)

3 Tension friction coupling to 9.5nm using torque wrench , then insert gearbox bung . Write torque setting on indicated face

4 Fit protection shroud

Étape 8 - Fit mounting brackets

Fit 4 off mounting brackets for later installation to main saw frame

PICTURES REQUIRED PLEASE

en none 0 Draft