R000569E Bench Assemble Head Spindle Posts

bench assembly instructions for saw cut axis

Difficulté

Hard Difficile

Durée

2 hour(s) heure(s)

R000569E_Bench_Assemble_Head_Spindle_Posts_Screenshot_2023-09-13_082307.png

Introduction

Tools Required

Standard Hex key set

Standard spanner set

Internal circlip pliers

Consumable 4mm yellow grease line

Pneumatic pipe cutters

Parts Required

B0000002 Bearing: 12/28dia x 8mm Sheilded x 2

B0000032 Linear Bearing: Ø30 x 50 Compact (Metal Case Only) x 4

B0001061 Grease fitting x 6

D0004001 Head Bearing Block x 3

D0004021 Upstroke Plate x 1

D0004078 Motor Plate (5311) x 1

D0004099 Cylinder Bearing Block x 1

D0004157 Motor plate spacer x 3

D0004256 Cylinder rod bar x 1

D0004343 Lower Damper Bracket (5313) x 1

D0004445 Semi circular slit strip (5533) 500mm x 1

D0004634 Chute Sawblade Strip 500mm (5532) x 1

D0004733 Belt Adjuster Pulley x 1

D0004734 Belt Adjusting Bar x 1

D0004735 Belt Adjuster Pin x 1

D0010780 Grease Manifold x 1

D0015490 Saw Turntable Sensor Flag x 1

D0015491 Saw Turntable Flag Bracket x 1

H0004444 Semi-circular Guard (5332) x1

P0000009 Fitting: 1/4 BSPT - 6mm Elbow x 2

P0000037 Magnetic Cylinder 40 x 185 with 15mm rod extension x 1

P0000308 Flow Controller In Line 6mm x 1

Étape 1 - Unless otherwise stated

All bolts to have Loctite 243 adhesive applied unless otherwise stated

All Threaded Pneumatic connections to have Loctite 570 applied

All bolts to be pen marked once adhesive applied and correct tension added

Étape 2 - Check upstroke plate

Check upstroke plate has helicoils fitted in indicated holes.

M8 thread will be present if they have, thread will be larger than M8 if they havent

Use workshop helicoil kit and add M8 x 1.5 od helicoils if not present

Étape 3 - Assemble cut strip assembly

1 Assemble D0004445 Semi circular slit strip onto D0004634 Chute Sawblade Strip as shown using 2 of M6 x 30 socket caps. Ensure all edges of parts are aligned flush when assembled

2 Fit H0004444 Semi-circular Guard as shown using M5 x 10 countersunk bolts

...Countersunk bolts must sit flush on guard panel. Use countersink tool to deepen if they sit proud

Étape 4 - Assemble cylinder

1 Attach 2 off P0000009 Fitting as shown

2 Attach D0004256 Cylinder rod bar as shown, and finalise lock nut

3 Attach P0000308 Flow Controller In Line 6mm to indicated fitting and connect with a 30mm long piece of 6mm black air pipe

Étape 5 - Assemble cylinder mount bearing block

1 Degrease D0004099 Cylinder Bearing Block and fit 1 off B0000032 Linear Bearing. Ensure yellow seal of bearing is on indicated face

2 Add M6 x 6 grubscrew to indicated hole and secure with Loctite 572

3 Fit 2 off B0001061 Grease fitting to indicated points

4 Assemble D0010780 Grease Manifold as shown using 1 off B0001061 grease fitting and 3 off B0000234 grease nipples (consumable stock)

5 Fit to bearing block using 2 off M4 x 16 socket caps

6 Fit 1 off B0000234 grease nipple to indicated point

Étape 6 - Assemble bearing blocks

1 Fit B0000032 Linear Bearing with yellow seal to indicated face of D0004001 Head Bearing Block

2 Fit B0001061 grease fitting to indicated face

3 Fit M6 x 6 blanking grubscrew to indicated face

Assemble 3 off in total as above

Étape 7 - Mount Bearing blocks

1 Mount cylinder bearing block and 2 off bearing block as indicated to D0004021 Upstroke Plate. Lightly secure with M6 x 25 socket caps and A form washers . Do not apply adhesive

2 Mount remaining bearing block as shown, incorporating D0004343 Lower Damper Bracket as shown . Use M6 x 25 socket caps, again do not apply adhesive or apply final tension

Étape 8 - Assemble rear grease line

1 Fit 3 off m4 tie bases and secure with M4 x 6 button heads at indicated points

2 fit and secure 2 lengths of 4mm yellow grease line and secure as shown

Étape 9 - Add front grease line

1 Add 3 off m4 tie base and secure with M4 x 6 button screws as shown

2 Cut and fit 1 off yellow grease pipe to follow route indicated

Étape 10 - Assemble tensioner pulley

1 Add two internal circlips (size required ) to D0004733 Belt Adjuster Pulley

2 Fit 2 off B0000002 Bearing to pulley as indicated. Be observant of bearing fit, if bearing fit is loose use Degreaser and apply Loctite 641

If fit is tight ,check components to drawings

3 Fit D0004735 Belt Adjuster Pin as shown, observing above regarding correct fitment

Étape 11 - Mount pulley to adjuster bar and motor plate

1 Fit pulley as shown to D0004734 Belt Adjusting Bar using M8 x 50 socket cap, M8 penny washer and backed off with M8 standard nut.

2 Fit assembly to D0004078 Motor Plate as shown using M8 x 35 socket cap and Heavy duty M8 washer

Étape 12 - Fit Motor plate

1 Fit motor plate to upstroke plate , combing part D0015491 Saw Turntable Flag Bracket and using D0004157 Motor plate spacer x 3 between upstroke plate and motor plate.

M8 x 40 socket cap 1 off

M8 x 50 socket cap 2 off

3 off M8 motor plate washers

2 Mount D0015490 Saw Turntable Sensor Flag using 2 off M6 x 20 socket caps and A form washers

en none 0 Draft