[version en cours de rédaction] | [version en cours de rédaction] |
Ligne 79 : | Ligne 79 : | ||
|Step_Title=<translate>Check laser alignment</translate> | |Step_Title=<translate>Check laser alignment</translate> | ||
|Step_Content=<translate>With the laser still casting along the infeed table, slowly return the gripper along the axis and inspect the laser dot in relation to lines added to gripper. Discrepancy should be less than 4mm on both axis</translate> | |Step_Content=<translate>With the laser still casting along the infeed table, slowly return the gripper along the axis and inspect the laser dot in relation to lines added to gripper. Discrepancy should be less than 4mm on both axis</translate> | ||
+ | |Step_Picture_00=R0008013_Clacker_assembly_quality.png | ||
+ | }} | ||
+ | {{Tuto Step | ||
+ | |Step_Title=<translate>Quality Check</translate> | ||
+ | |Step_Content=<translate>All settings should be double checked once final adjustments have been made | ||
+ | |||
+ | Machine level | ||
+ | |||
+ | Laser alignment | ||
+ | |||
+ | Grip pin positions | ||
+ | |||
+ | Back fence alignments</translate> | ||
|Step_Picture_00=R0008013_Clacker_assembly_quality.png | |Step_Picture_00=R0008013_Clacker_assembly_quality.png | ||
}} | }} |
Details for correct alignment and process steps
Auteur Gareth Green | Dernière modification 5/03/2024 par Gareth Green en cours de rédaction ⧼frevu-button-review-label⧽
Details for correct alignment and process steps
ZX5_Production_R0015040_Module_F_to_R0015001B_Module_E_alignment_Screenshot_2023-12-08_135219.png
Position module F at end of Module E infeed frame
Approximately Align Saw roller back fences to Saw infeed back fences
Approximately align X axis position by setting the to frames spaced at the distance shown of 20mm
Use the indicated points to level the frame.
Use cut table indicated as levelling point
Level Y and X Axis of saw
It is vital to confirm Cut tables are in the correct position once levelled, and that movement has occurred during transport
To do this the base of the saw turn table must be checked for level. These readings must read exactly the same as the levelled cut table in the previous step
Any discrepancy should be reported
Saw module should be raised or lowered to align with blue load rollers on saw infeed table
Saw module should sit above blue rollers by no more than 1mm
Ensure levels previously set are not compromised when adjusting height
Double check levels are still correct once height has been adjusted
1 Position base of laser against back fence rollers and cast beam towards gripper
2 Position Gripper directly Infront of laser and mark vertical line on gripper to match laser dot
3 Rotate laser so base is on cut table and mark a horizontal line on the gripper to match the laser dot
3 Move Gripper to point one indicated , and inspect horizontal line to laser dot . Any discrepancy can be adjusted by the 2 off adjusting floor bolts directly below
4 Repeat this step and indicated points 2,3 and 4
Rotate the laser so the base is against the rear roller fence, and ensure the gripper is at its furthest point of travel away from the saw . Project the laser to the gripper. Adjust Saw module in directions shown to align the laser to the vertical mark on gripper
With the laser still casting along the infeed table, slowly return the gripper along the axis and inspect the laser dot in relation to lines added to gripper. Discrepancy should be less than 4mm on both axis
All settings should be double checked once final adjustments have been made
Machine level
Laser alignment
Grip pin positions
Back fence alignments
en none 0 Draft
Vous avez entré un nom de page invalide, avec un ou plusieurs caractères suivants :
< > @ ~ : * € £ ` + = / \ | [ ] { } ; ? #