[version en cours de rédaction] | [version en cours de rédaction] |
m (Gareth Green a déplacé la page R0015094 Bench Assemble shafts, Bearings and Pinions vers R0015254 Bench Assemble shafts, Bearings and Pinions) |
|||
Ligne 60 : | Ligne 60 : | ||
shafts</translate> | shafts</translate> | ||
+ | |Step_Picture_00=R0015254_Bench_Assemble_shafts__Bearings_and_Pinions_Screenshot_2023-09-07_143739.png | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
Ligne 73 : | Ligne 74 : | ||
3 Use Fe10 solvent to remove any contamination</translate> | 3 Use Fe10 solvent to remove any contamination</translate> | ||
+ | |Step_Picture_00=R0015254_Bench_Assemble_shafts__Bearings_and_Pinions_Screenshot_2023-09-07_143801.png | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
Ligne 86 : | Ligne 88 : | ||
3 Use Fe10 solvent to remove any contamination</translate> | 3 Use Fe10 solvent to remove any contamination</translate> | ||
+ | |Step_Picture_00=R0015254_Bench_Assemble_shafts__Bearings_and_Pinions_Screenshot_2023-09-07_143825.png | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
Ligne 105 : | Ligne 108 : | ||
* If all pinions ( Or most off) are tight , polish main shaft down with emery tape 180 to remove high spot | * If all pinions ( Or most off) are tight , polish main shaft down with emery tape 180 to remove high spot | ||
{{Warning|...When performing any adjustments using emery tape., parts must be thoroughly cleaned before trial fitting again as grit residue can caused components to bind together on assembly}}</translate> | {{Warning|...When performing any adjustments using emery tape., parts must be thoroughly cleaned before trial fitting again as grit residue can caused components to bind together on assembly}}</translate> | ||
+ | |Step_Picture_00=R0015254_Bench_Assemble_shafts__Bearings_and_Pinions_Screenshot_2023-09-07_143848.png | ||
+ | |Step_Picture_01=R0015254_Bench_Assemble_shafts__Bearings_and_Pinions_Screenshot_2023-09-07_143913.png | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
Ligne 111 : | Ligne 116 : | ||
2 Use grease gun to grease bearings to aid assembly</translate> | 2 Use grease gun to grease bearings to aid assembly</translate> | ||
+ | |Step_Picture_00=R0015254_Bench_Assemble_shafts__Bearings_and_Pinions_Screenshot_2023-09-07_143938.png | ||
+ | |Step_Picture_01=R0015254_Bench_Assemble_shafts__Bearings_and_Pinions_Screenshot_2023-09-07_143959.png | ||
}} | }} | ||
{{Notes}} | {{Notes}} |
Bench assembly instructions for drive components
Auteur Gareth Green | Dernière modification 11/12/2023 par Gareth Green en cours de rédaction ⧼frevu-button-review-label⧽
Bench assembly instructions for drive components
R0015094_Bench_Assemble_shafts__Bearings_and_Pinions_Screenshot_2023-06-12_094818.png
Tools Required
Compressed air line
180 grit emery tape
Fe10 solvent
Cleaning cloth
Standard Hex key set
Standard spanner set
Grease gun
Parts Required
D0015556 x 2
D0015555x 2
B0001094 x 18
B0000228 x 18
Please take pictures of these steps and add to comments section on mondays for this dokit please
Ensure shafts D0015556 2 off and D0015555 2 off are clean before trial fitting .
1 check for any burrs or damage to shafts . Remove with File/emery tape 180 grit if present
2 Use compressed air to clean debris from all keyways on shafts .
3 Use Fe10 solvent to remove contaminants on
shafts
Ensure bearings B0000228 18 off are clean before trial fitting
1 Check for any internal burrs especially around grubscrew point .
If present remove with emery tape 180 grit
2 Use compressed air to remove and debris
3 Use Fe10 solvent to remove any contamination
Ensure B0001094 Pinions 18 off are clean before trial fitting
1 Check for any internal burrs especially around grubscrew point .
If present remove with emery tape 180 grit
2 Use compressed air to remove and debris
3 Use Fe10 solvent to remove any contamination
Check the following
1 Every B0000228 bearing passes freely over each shaft
2 Every B0001094 pinion passes freely over each shaft
If tight spots are found, these steps should be followed
1 Attach supplied grease points and covers to B0000228 bearings (18 off)
2 Use grease gun to grease bearings to aid assembly
en none 0 Draft
Vous avez entré un nom de page invalide, avec un ou plusieurs caractères suivants :
< > @ ~ : * € £ ` + = / \ | [ ] { } ; ? #