|
|
| Ligne 9 : |
Ligne 9 : |
| | }} | | }} |
| | {{Introduction | | {{Introduction |
| − | |Introduction=<translate>'''<u>Tools Required</u>''' | + | |Introduction=<translate>28/08/2025 |
| | | | |
| | | | |
| − | '''<u>Parts Required</u>'''
| + | Moved to Confluance |
| | | | |
| − | D0015513 Arm brace x 2
| |
| | | | |
| − | D0015514 Arm brace x 1 </translate>
| + | Click [https://stuga-ltd.atlassian.net/wiki/external/MDZkMzA2NGQzNjVhNGJjOThkYzI5MjM4ZjlkMTA2M2E Here]</translate> |
| | }} | | }} |
| | {{Materials}} | | {{Materials}} |
| | {{EPI}} | | {{EPI}} |
| | {{Tuto Step | | {{Tuto Step |
| − | |Step_Title=<translate>Prepare area for testing</translate> | + | |Step_Title=<translate></translate> |
| − | |Step_Content=<translate>Ensure area is clear and free from personnel</translate>
| |
| − | }}
| |
| − | {{Tuto Step
| |
| − | |Step_Title=<translate>Connect mains air supply</translate>
| |
| − | |Step_Content=<translate>Connect mains air supply and check for any leaks present is components natural state</translate>
| |
| − | }}
| |
| − | {{Tuto Step
| |
| − | |Step_Title=<translate>check home positions</translate>
| |
| − | |Step_Content=<translate>Check home positions are correct in natural state
| |
| − | | |
| − | | |
| − | Loader wheel Y154 should be up away from roller beds in home position
| |
| − | | |
| − | | |
| − | Roller beds Y157 should be in the up position in home position
| |
| − | | |
| − | | |
| − | Blowers Y375 should be switched off in the home position</translate>
| |
| − | }}
| |
| − | {{Tuto Step
| |
| − | |Step_Title=<translate>Test Y154 output</translate>
| |
| − | |Step_Content=<translate>On valve bank, manually fire Y154 output.
| |
| − | | |
| − | | |
| − | Check for air leaks when output is fired
| |
| − | | |
| − | | |
| − | Check regulator shows pressure when fired by increasing pressure with adjusted .Once confirmed correct operation, a djust regulator to 1 bar or 0.1 mpa</translate>
| |
| − | }}
| |
| − | {{Tuto Step
| |
| − | |Step_Title=<translate>Test Y157 Output</translate>
| |
| − | |Step_Content=<translate>On valve bank, manually fire valve Y157 roller lift output
| |
| − | | |
| − | | |
| − | All rollers should drop down into position. When fired, check there are no air leaks present in the active position</translate>
| |
| − | }}
| |
| − | {{Tuto Step
| |
| − | |Step_Title=<translate>Test Y375 Output</translate>
| |
| − | |Step_Content=<translate>Manually fire Y357 output Check each blowers flow regulator can adjust flow rate when turned . Once confirmed , fully close flow regulator and wind out 2 turns</translate>
| |
| − | }}
| |
| − | {{Tuto Step
| |
| − | |Step_Title=<translate>Disconnect air supply</translate>
| |
| | |Step_Content=<translate></translate> | | |Step_Content=<translate></translate> |
| − | }}
| |
| − | {{Tuto Step
| |
| − | |Step_Title=<translate>Fit brace 1</translate>
| |
| − | |Step_Content=<translate>Fit D0015513 at load motor end of frame .
| |
| − |
| |
| − | Use M8 x 35 socket caps, M8 motor plate washers and M8 nyloc nuts .</translate>
| |
| − | |Step_Picture_00=R0015268_Pneumatic_module_Test_Screenshot_2023-12-11_111307.png
| |
| − | |Step_Picture_01=R0015266B_mount_completed_assemblies_photorequired.png
| |
| − | }}
| |
| − | {{Tuto Step
| |
| − | |Step_Title=<translate>Fit brace 2</translate>
| |
| − | |Step_Content=<translate>fit second brace D00155122</translate>
| |
| − | |Step_Picture_00=R0015268_Pneumatic_module_Test_Screenshot_2023-12-11_111413.png
| |
| − | |Step_Picture_01=R0015266B_mount_completed_assemblies_photorequired.png
| |
| − | }}
| |
| − | {{Tuto Step
| |
| − | |Step_Title=<translate>Fit brace 3</translate>
| |
| − | |Step_Content=<translate>Fit D0015514 at final position . Add M8 motor plate washer as spacer as shown</translate>
| |
| − | |Step_Picture_00=R0015268_Pneumatic_module_Test_Screenshot_2023-12-11_111845.png
| |
| − | |Step_Picture_01=R0015268_Pneumatic_module_Test_Screenshot_2023-12-11_111852.png
| |
| − | |Step_Picture_02=R0015266B_mount_completed_assemblies_photorequired.png
| |
| | }} | | }} |
| | {{Notes}} | | {{Notes}} |
Français
English
Deutsch
Español
Italiano
Português