[version en cours de rédaction] | [version en cours de rédaction] |
(Page créée avec « {{Tuto Details |Description=<translate>Critical measurements and settings for an Autoflow infeed table</translate> |Categories=Software }} <translate><br /> = Method =... ») |
|||
Ligne 5 : | Ligne 5 : | ||
<translate><br /> | <translate><br /> | ||
− | = Method = | + | =Method= |
{{Warning|...Make sure the GX axis is scaled correctly before starting any measurements}}{{Warning|...Ensure the infeed is set at the correct distance from the machining centre (500mm between feet centreline}}<br /> | {{Warning|...Make sure the GX axis is scaled correctly before starting any measurements}}{{Warning|...Ensure the infeed is set at the correct distance from the machining centre (500mm between feet centreline}}<br /> | ||
− | * Use the gripper arm as the measuring stick. The datum must be set so that zero is the spindle centreline. | + | *Use the gripper arm as the measuring stick. The datum must be set so that zero is the spindle centreline. |
− | * The measure point is when the gripper nose switch is depressed | + | *The measure point is when the gripper nose switch is depressed |
{| class="wikitable" | {| class="wikitable" | ||
Ligne 37 : | Ligne 37 : | ||
|Distance from zero to profile load fence | |Distance from zero to profile load fence | ||
|600 | |600 | ||
+ | | | ||
+ | |- | ||
+ | |stopCylinderToZeroX | ||
+ | | | ||
+ | | | ||
| | | | ||
|- | |- | ||
Ligne 49 : | Ligne 54 : | ||
|GX Move After Datum | |GX Move After Datum | ||
|Ideally set to max profile length+infeedZeroToX+100{{Warning|...Must not exceed GX Max pos}} | |Ideally set to max profile length+infeedZeroToX+100{{Warning|...Must not exceed GX Max pos}} | ||
− | |||
|6500+600+100 | |6500+600+100 | ||
=7200 | =7200 | ||
+ | | | ||
+ | |- | ||
+ | |GX Minimum Position | ||
+ | |Absolute minimum position of GX | ||
+ | Goal is for gripper nose switch to at least reach saw blade | ||
+ | {{Warning|...Take care with clashing of the Gripper Froward clamp with the MH infeed clamp}} | ||
+ | Ensure the end rubber buffers are set to prevent a mechanical clash beween the | ||
+ | | -1050 | ||
+ | | | ||
+ | |- | ||
+ | |Infeed Horizontal side clamp positions | ||
+ | |These are set up in the clamp setup as the "GripPos" for OuA_P2BFOnx{{Info|...Note - bar end should be set to -9999, as this effectively disables the other end of the bar from influencing the clamp on/off cycle}}<br /> | ||
+ | |1-950 | ||
+ | 2-1480 | ||
+ | |||
+ | 3-2600 | ||
+ | |||
+ | 4-3700 | ||
+ | |||
+ | 5-4800 | ||
+ | |||
+ | 6-6300 | ||
+ | |||
+ | 7-7050 | ||
+ | | | ||
+ | |- | ||
+ | |GY Min Position | ||
+ | |Limited by the backfence clamping in the saw area | ||
+ | |10 | ||
+ | | | ||
+ | |- | ||
+ | |GY Max Position | ||
+ | | | ||
+ | |54 | ||
+ | | | ||
+ | |- | ||
+ | |GZ Min Position | ||
+ | |Gripper must not bottom out on the saw tables | ||
+ | |6 | ||
+ | | | ||
+ | |- | ||
+ | |GZ Max position | ||
+ | |{{Info|...GY and GZ min / max positions and gripper tooth height (PullGripperHeight) should also be set in the file c:\ddrive\draw.mul}} | ||
+ | |70 | ||
| | | | ||
|}</translate> | |}</translate> | ||
{{PageLang | {{PageLang | ||
+ | |Language=en | ||
|SourceLanguage=none | |SourceLanguage=none | ||
|IsTranslation=0 | |IsTranslation=0 | ||
− | |||
}} | }} | ||
{{AddComments}} | {{AddComments}} |
Critical measurements and settings for an Autoflow infeed table
Auteur Gareth Green | Dernière modification 27/02/2023 par Gareth Green en cours de rédaction ⧼frevu-button-review-label⧽
Pas encore d'image
Critical measurements and settings for an Autoflow infeed table
Measurement | Description | A2027 Value | Photo |
---|---|---|---|
Machining Centre to Infeed spacing | DDistance between centrelines of feet | 500 | |
Zero Datum | Centreline of spindles | 0 | |
measureStartPosX | Measuring start position
Should be so that measure sensor is on machining centre side of the profile load fence |
-880 | |
infeedToZeroX | Distance from zero to profile load fence | 600 | |
stopCylinderToZeroX | |||
GX Axis Max position | Maximum travel on GX Axis
After datum, press estop and manually move to end of travel Note the value and subtract 10mm |
7255 | |
GX Move After Datum | Ideally set to max profile length+infeedZeroToX+100 ...Must not exceed GX Max pos
|
6500+600+100
=7200 |
|
GX Minimum Position | Absolute minimum position of GX
Goal is for gripper nose switch to at least reach saw blade ...Take care with clashing of the Gripper Froward clamp with the MH infeed clamp
Ensure the end rubber buffers are set to prevent a mechanical clash beween the |
-1050 | |
Infeed Horizontal side clamp positions | These are set up in the clamp setup as the "GripPos" for OuA_P2BFOnx ...Note - bar end should be set to -9999, as this effectively disables the other end of the bar from influencing the clamp on/off cycle
|
1-950
2-1480 3-2600 4-3700 5-4800 6-6300 7-7050 |
|
GY Min Position | Limited by the backfence clamping in the saw area | 10 | |
GY Max Position | 54 | ||
GZ Min Position | Gripper must not bottom out on the saw tables | 6 | |
GZ Max position | ...GY and GZ min / max positions and gripper tooth height (PullGripperHeight) should also be set in the file c:\ddrive\draw.mul
|
70 |
en none 0
Draft
Vous avez entré un nom de page invalide, avec un ou plusieurs caractères suivants :
< > @ ~ : * € £ ` + = / \ | [ ] { } ; ? #