Stuga Flowline Overhaul Particulars

Details of the components replaced on a Flowline Overhaul

overhaul Beckhoff_AX8000_Flowline_Upgrade_Pusher_Motor.JPEG

Overview

The Flowline was manufactured from 2000 to 2005, and all 76 machines are still in production today, outliving the expected design lifespan of 10 years and proving the machines’ long term reliability and suitability for the market place.

By 2019, 27 of the original machines have been fully overhauled and resold to new and existing customers, each with a full one year warranty from Stuga.

As with any cutting-edge technology, the drive systems and control components have been made obsolete by the original manufacturers, and so Stuga have kept up to date with an upgrade package to the latest control systems. The newer systems are more dynamic and reliable and allow these improvements to be passed on to the refurbished machines. A refurbished model is faster, more reliable and easier to use than the original model.

Overhaul Particulars

• Paint touch up to remove rust and bare metal surfaces
• Upgrade guarding all round to 2019 specification
• Replace all control system with latest Beckhoff control
  • Control PC and PLC – Windows 10
  • I/O interfaces
  • Servo Drives
  • Servo Motors
  • Cables
  • 2 off monitors
• Latest control software with graphical user interface and production timing reports

• Camera Diagnostic system
• Replace label printer
• Replace axis gearboxes
• Replace main rotary ring and journals
• Replace X axis and saw pusher linear rails and journals, including pinion gears
• Replace worn cylinders where necessary
• Replace worn bearings where necessary
• Replace Valve banks and broken regulators
• Replace contactors where necessary
• New dual bag extraction system
• Additional Upgrades to improve performance
  • Side Roller guidefence on Saw
  • Rear guidefence on Machining centre outfeed clamps
  • Saw Eject conduit replacement
  • Grease nipple addition on eject and saw cut shafts
  • Outfeed Safety Gate
  • Offcut Measuring system – measures offcuts as they are loaded and reoptimizes automatically

Control Components Components Replaced

Component	Location	Quantity	Picture
Beckhoff Control PC	Machining Centre Cabinet	1
Beckhoff IO Modules	Machining Centre Cabinet Transfer Table Cabinet Saw Cabinet	3
Beckhoff AX8000 series Dual Servo Drives	Machining Centre Cabinet	3
Front End Interface PC and Touchscreen Monitors (Windows 10)	Machining Centre Cabinet	1
Beckhoff Servo Motors and Cabling	X axis, Y axis, Z axis R axis, Saw Pusher	6
Gearboxes	X axis, Saw Pusher, R axis	3

Tru-Loc Gripper Upgrade

All overhaul machines are supplied with the Tru-Loc gripper system, a dual-tooth fixed gripper design that accurately and reliably locates into the profile

• Tapered pins on both sides of machine ensure an accurate and reliable datum
• 2 holes and pins are used to cover all profile types - this eliminates the need for a "G" axis sideways movement on the gripper
• Eliminates gripper slip
• Allows a more dynamic acceleration and deceleration on all x axis movements, therefore improving cycle time

Optional Extras

The performance of the machine can be enhanced with a “High Speed Ring” upgrade (R0010200C). This improves the original Flowline design and brings it in line in terms of performance with a modern “ZX3” machine.

What is involved?

The upgrade consists of a mechanical and electrical upgrade to the ring spindles. Four of the current spindle heads will be removed, and in their place are fitted 4 higher power, higher speed units, with two “Double Plunge” assemblies. This improves the machining cycle time of trickle vents, doors and letter boxes by over 300%. The improvements are gained by using higher specification spindle motors, higher quality tooling and (if applicable) by machining both sides of the profile at the same time. With these changes, it is possible to improve the current machine output by up to 50%, depending on your machine setup. A full assessment of the time saved can be undertaken on your machine on request.

How can it be so much faster?

	Standard     Flowline	With Upgrade
Spindle Speed	11,000 rpm	18,000 rpm
Spindle Power at Tool	0.2kW	0.75kW
Tooling	Standard	Carbide
Time Taken for 4000 Trickle Vent	55 sec	15 sec
Time Taken for Door Handle Prep	90 sec	35 sec

Apart from the obvious fact of cutting both sides of the profile at the same time, there are other speed improvements:

• When the original flowline was designed in 1999, trickle vents were a small part of production (around 20%). In the years since, regulations have meant that a considerably higher percentage of frames need a trickle vent. This has put a much higher overhead on the machining side, slowing the entire machine down. With our upgrade, the balance between sawing and machining is redressed, allowing the machine side to keep up with the saw.
• The spindle speed is 50% faster allowing faster cutting.
• Stuga have also worked closely with tooling manufacturers, and coupled with the increased spindle speed, the tools can cut up to 4 times faster. The quality of cut and cutter life has also been improved.

en none 0

Draft