| [version en cours de rédaction] | [version en cours de rédaction] |
| Ligne 69 : | Ligne 69 : | ||
|Step_Title=<translate>Test axis Datuming</translate> | |Step_Title=<translate>Test axis Datuming</translate> | ||
|Step_Content=<translate></translate> | |Step_Content=<translate></translate> | ||
| + | }} | ||
| + | {{Tuto Step | ||
| + | |Step_Title=<translate>Check Spindles and alarms</translate> | ||
| + | |Step_Content=<translate>Check inverter is wired so that OK=high on X90 | ||
| + | |||
| + | Check alarms trigger on low signal on inverter ok | ||
| + | |||
| + | Check 50Hz and 300Hz spindles function correctly from SpindleIO screen | ||
| + | |||
| + | {{Info|...A lot of the older machines were released with inverter OK active low, and the alarms file set up to "bodge" around this. The "correct" way should be active high which means it is also fail safe. Take this opportunity to ensure the machine is correct}}<br /></translate> | ||
}} | }} | ||
{{Notes}} | {{Notes}} | ||
Version du 30 juin 2020 à 19:48
Steps to upgrading an Autoflow to Windows 10, replacing both the front end and back end PCs
Difficulté
Difficile
Durée
1 jour(s)
Sommaire
- 1 Introduction
- 2 Étape 1 - Set up the 6017 PC
- 3 Étape 2 - Set up New Camera PC
- 4 Étape 3 - Add the backup to cameraPC
- 5 Étape 4 - Convert the TC2 project from old machine
- 6 Étape 5 - Install the new PCs on site
- 7 Étape 6 - Set up the IP addresses
- 8 Étape 7 - Test all IO
- 9 Étape 8 - Test axis directions
- 10 Étape 9 - Test axis Datuming
- 11 Étape 10 - Check Spindles and alarms
- 12 Commentaires
Introduction
Upgrading an Autoflow to Windows 10 involves upgrading two PCS
- The Beckhoff control PC
- The Camera PC
The Beckhoff PC is not upgradable so needs to be completely replaced. We use the miniature Beckhoff C6017 for this
Étape 1 - Set up the 6017 PC
- Ensure regional settings correct - correct date format
- Rename the Ethernet Adaptors to Ethernet and EtherCAT
- Ensure the TwinCAT Protocol is installed on the EtherCAT adaptor
- Teamviewer setup
- Administrator password set to "Stuga001"
- Add Stuga desktop image
- Latest winMulti in c:\multi
Étape 2 - Set up New Camera PC
Follow standard Setup procedure to step 5 to ensure sourcetree installed with latest tc3Multi software pulled to machine
Étape 3 - Add the backup to cameraPC
In folder c:\DDRIVE
Copy latest messages.saw to DDRIVE
Étape 4 - Convert the TC2 project from old machine
Follow this procedure to convert the project
Étape 5 - Install the new PCs on site
- Ensure the 6017 PC has been earthed adequately
Étape 6 - Set up the IP addresses
Map the network drives
Map customer network connections
Étape 7 - Test all IO
This is important to ensure there have been no mistakes in the remapping
Étape 8 - Test axis directions
Étape 9 - Test axis Datuming
Étape 10 - Check Spindles and alarms
Check inverter is wired so that OK=high on X90
Check alarms trigger on low signal on inverter ok
Check 50Hz and 300Hz spindles function correctly from SpindleIO screen
Draft
Français
English
Deutsch
Español
Italiano
Português