|
|
| (4 révisions intermédiaires par le même utilisateur non affichées) |
| Ligne 9 : |
Ligne 9 : |
| | }} | | }} |
| | {{Introduction | | {{Introduction |
| − | |Introduction=<translate><u>'''Tools Required'''</u> | + | |Introduction=<translate>15/09/2025 |
| | | | |
| | | | |
| − | standard hex key set
| + | Moved to Confluance |
| | | | |
| − | Standard spanner set
| |
| | | | |
| − | Standard HSS drill set
| + | Click [https://stuga-ltd.atlassian.net/wiki/external/OTc1M2UzNWE1ZWY0NGZkNWFkZTA4ZDgyZTEwYWE5NjU Here]</translate> |
| − | | |
| − | Standard tap set
| |
| − | | |
| − | Long reach 4.2mm drill
| |
| − | | |
| − | Extended M5 tap
| |
| − | | |
| − | | |
| − | | |
| − | <u>'''Parts Required'''</u>
| |
| − | | |
| − | | |
| − | R0015321 Bench assemble guards and doors
| |
| − | | |
| − | <br /></translate>
| |
| | }} | | }} |
| | {{Materials}} | | {{Materials}} |
| | {{EPI}} | | {{EPI}} |
| | {{Tuto Step | | {{Tuto Step |
| − | |Step_Title=<translate>Unless otherwise stated</translate> | + | |Step_Title=<translate></translate> |
| − | |Step_Content=<translate>Use locktite 243 on all fasteners | + | |Step_Content=<translate></translate> |
| − | | |
| − | Use loctite 572 on all threaded pneumatic connection
| |
| − | | |
| − | Pen mark all fasteners to show finalised</translate>
| |
| − | |Step_Picture_00=R0015086_Assemble_Pneumatics_on_to_electrical_cabinet_loctite_243.png
| |
| − | }}
| |
| − | {{Tuto Step
| |
| − | |Step_Title=<translate>Fit roof panel</translate>
| |
| − | |Step_Content=<translate>Fit pre assembled roof panel</translate>
| |
| − | |Step_Picture_00=R0015319_Fit_Guards_and_Doors_Screenshot_2023-11-01_164305.png
| |
| − | }}
| |
| − | {{Tuto Step
| |
| − | |Step_Title=<translate>Fit rear panel</translate>
| |
| − | |Step_Content=<translate>Fit re assembled rear panel
| |
| − | | |
| − | | |
| − | | |
| − | Secure with 7 off M6 x 12 socket caps and M6 A form washers</translate>
| |
| − | |Step_Picture_00=R0015319_Fit_Guards_and_Doors_Screenshot_2023-11-01_164142.png
| |
| − | |Step_Picture_01=R0015319_Fit_Guards_and_Doors_Screenshot_2025-01-08_085715.png
| |
| − | }}
| |
| − | {{Tuto Step
| |
| − | |Step_Title=<translate>Alignment</translate>
| |
| − | |Step_Content=<translate>It is vital that door locks should align correctly.
| |
| − | | |
| − | | |
| − | Handle operation should be smooth and no force required to engage locking pins
| |
| − | | |
| − | Any discrepancies should be reported</translate>
| |
| − | |Step_Picture_00=R0008013_Clacker_assembly_quality.png
| |
| − | }}
| |
| − | {{Tuto Step
| |
| − | |Step_Title=<translate>Fit Guard Doors</translate>
| |
| − | |Step_Content=<translate>Fit 4 off Pre assembled guard doors to hinges</translate>
| |
| − | |Step_Picture_00=R0015319_Fit_Guards_and_Doors_Screenshot_2023-11-01_164459.png
| |
| − | }}
| |
| − | {{Tuto Step
| |
| − | |Step_Title=<translate>Drill door lock pins</translate>
| |
| − | |Step_Content=<translate>Drill off door lock pins and strike plates</translate>
| |
| − | |Step_Picture_00=R0015319_Fit_Guards_and_Doors_Screenshot_2023-11-01_164556.png
| |
| − | }}
| |
| − | {{Tuto Step
| |
| − | |Step_Title=<translate>Drill and set interlock switches</translate>
| |
| − | |Step_Content=<translate>Set and drill door interlock switches
| |
| − | | |
| − | | |
| − | Ensure door switches are set correctly. Interlock blade must fully penetrate the guard switch, and align with no catching as entering the interlock</translate>
| |
| − | |Step_Picture_00=R0015319_Fit_Guards_and_Doors_Screenshot_2023-11-01_164556.png
| |
| − | }}
| |
| − | {{Tuto Step
| |
| − | |Step_Title=<translate>Fit Front panel</translate>
| |
| − | |Step_Content=<translate>Fit front upper front panel</translate>
| |
| − | |Step_Picture_00=R0015319_Fit_Guards_and_Doors_Screenshot_2023-11-01_164125.png
| |
| | }} | | }} |
| | {{Notes}} | | {{Notes}} |
Français
English
Deutsch
Español
Italiano
Português