R0015336 Pneumatic Output Testing : Différence entre versions

[version en cours de rédaction]

Version actuelle datée du 27 août 2025 à 13:35

Details for manual pneumatic output testing on module

Auteur Gareth Green | Dernière modification 27/08/2025 par Gareth Green en cours de rédaction ⧼frevu-button-review-label⧽

Difficulté

Moyen

Durée

1 heure(s)

Details for manual pneumatic output testing on module

Difficulté

Moyen

Durée

1 heure(s)

Introduction

27/08/2025

Moved to Confluence

Click Here

Étape 1 -

Commentaires

en none 0 Draft

@@ Ligne 9 : / Ligne 9 : @@
 }}
 {{Introduction
-|Introduction=<translate><u>'''Tools Required'''</u>
+|Introduction=<translate>27/08/2025
-PCL airline connection
+Moved to Confluence
-mm blanking ports
-Valve Manual over ride tool
+Click [https://stuga-ltd.atlassian.net/wiki/external/ZjJkMDQ0MDA4NWNhNGY1OGE2ODIxN2EwNmZjNGFhZjQ Here]</translate>
-Standard screwdriver set
-<u>'''Parts required'''</u>
-R0015040 completed module</translate>
 }}
 {{Materials}}
 {{EPI}}
 {{Tuto Step
-|Step_Title=<translate>Safety</translate>
+|Step_Title=<translate></translate>
-|Step_Content=<translate>Output testing will require valve operation with no e/s circuit
+|Step_Content=<translate></translate>
-Ensure the following
-Work area is clear from all components not required for testing
-All colleagues are aware of the procedure being undertaken
-No additional colleagues are working on the module
-PCL coupling is accessible to release pressure in case of emergency
-Testing procedure is fully adhered to</translate>
-|Step_Picture_00=R0015338_Bench_Assemble_Serial_Plate_caution.png
-}}
-{{Tuto Step
-|Step_Title=<translate>Set Air service unit soft start</translate>
-|Step_Content=<translate>Wind fully out soft start screw situated on top on main air service unit</translate>
-|Step_Picture_00=R0015336_Pneumatic_Output_Testing_Screenshot_2023-10-23_135953.png
-}}
-{{Tuto Step
-|Step_Title=<translate>Check all open ports</translate>
-|Step_Content=<translate>Ensure all open ports and trailing pipes are suitably blanked</translate>
-|Step_Picture_00=R0015336_Pneumatic_Output_Testing_Screenshot_2023-10-23_135953.png
-}}
-{{Tuto Step
-|Step_Title=<translate>Connect main PCL</translate>
-|Step_Content=<translate>Connect main pcl air feed to air service unit
-Increase Air service unit pressure to 6.0bar /6mpa</translate>
-|Step_Picture_00=R0015336_Pneumatic_Output_Testing_Screenshot_2023-10-23_135953.png
-}}
-{{Tuto Step
-|Step_Title=<translate>Check for leaks</translate>
-|Step_Content=<translate>Check for audible leaks on the red pipe lines installed and correct if found
-Check air gun regulator functions properly . Fully open the regulator (2 bar limited ) and test air gun assembly</translate>
-|Step_Picture_00=R0015336_Pneumatic_Output_Testing_Screenshot_2023-10-23_140328.png
 }}
 {{Notes}}
 {{PageLang
+|Language=en
 |SourceLanguage=none
 |IsTranslation=0
-|Language=en
 }}
 {{Tuto Status
 |Complete=Draft
 }}