R0015114 Bench Assemble Valve Banks and Regulators : Différence entre versions

[version en cours de rédaction]

Version actuelle datée du 3 avril 2024 à 11:01

Assembly details for pneumatic components

Auteur Gareth Green | Dernière modification 3/04/2024 par Gareth Green en cours de rédaction ⧼frevu-button-review-label⧽

Difficulté

Moyen

Durée

2.5 heure(s)

Assembly details for pneumatic components

Difficulté

Moyen

Durée

2.5 heure(s)

Sommaire

1 Introduction
2 Étape 1 - Unless otherwise stated
3 Étape 2 - Ecr raised
4 Étape 3 - Assemble valve bank
5 Étape 4 - Attach valve bank
6 Étape 5 - Assemble regulators
7 Étape 6 - Air service unit Handing
8 Étape 7 - Air dump over ride and pressure switch
9 Étape 8 - Mount air service unit
10 Étape 9 - Mount regulators
11 Étape 10 - Mount bulkheads
12 Étape 11 - Assemble and mount 0-2bar regulator
13 Étape 12 - Fit and connect air gun assembly
14 Étape 13 - Fit cable gland
15 Étape 14 - Fit labels for regulators
16 Étape 15 - Lower rear panel bulklheads
17 Étape 16 - Label bulkheads
18 Commentaires

Introduction

Tools Required

Standard hex key set

Standard spanner set

Standard HSS drill set

Standard tap set

Parts Required

H0007998 Regulator internal mount 5 way x 1

P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 14

P0000020 Fitting: Plug 1/8" BSP (Grubscrew Type) x 9

P0000021 air gun assembly x 1

P0000024 hex nipple 1/4 x 3

P0000058 Regulator Mounting Kit x 1

P0000074 Elbow Adaptor 8mm - 1/8 BSP (Pneumax not acceptable) x 2

P0000096 Fitting: Brass Reducing Bush 1/2 - 1/4 x 2

P0000142 Elbow Adaptor 8mm - 1/8 BSP x 2

P0000145 tee equal 1/4 x 3

P0000159 Fitting: Stem Blanking Plug 6mm x 2

P0000277 Fitting: Bulkhead Female 8mm x 1/4 BSP x 1

P0000278 Regulator 0-2 bar x 1

P0000332 Regulator with Gauge G1/8'' 0-8 bar x 8

P0000361 1/4'' Male Probe to suit 1/4'' PCL Female coupling x 1

P0000419 Air Service Unit OH (P0283) x 1

P0001071 Valve base type41 8 position x 1

P0001074 Fitting: 1/4" BSP Hex Head Silencer x 4

P0001101 Male straight 1/4 bsp to 12mm x 2

P0001102 Fitting male elbow 12mm 1/4 x 4

P0001105 Bulkhead straight 12mm x 6

P0001186 Valve. 24v dc smc x 8

Étape 1 - Unless otherwise stated

Use Loctite 243 on all fasteners

Use Loctite 572 on all threaded pneumatic connection

Pen mark all fasteners to show finalised

R0015086 Assemble Pneumatics on to electrical cabinet loctite 243.png

Étape 2 - Ecr raised

Ecr raised to amend regulator bracket to remove redundant holes and add fixing holes for valve bank

Use part as is until process to update is complete

Drill regulator bracket M4 to suit valve base

R0015114 Bench Assemble Valve Banks and Regulators Screenshot 2023-12-21 112846.png

Étape 3 - Assemble valve bank

Assemble valve bank

1 Prepare parts

2 Fit gasket to valves . Ensure gasket sits flat and aligned

3 Fit valves to valve bank base

4 Attach Air feed connection and exhausts

5 Add 6mm blanks

Étape 4 - Attach valve bank

Attach valve bank to regulator bracket using 4 off M4 x 40 socket caps , M4 washers and M4 nyloc nuts

Étape 5 - Assemble regulators

Ensure in and out ports at 90 degrees to each other are used as shown

1 Assemble 7 off regulators with 6mm elbows and spare port blanked

2 Assemble 1 off regulator with 8mm elbows and spare port blanked

Étape 6 - Air service unit Handing

Reference for assembly of handed variants

R-L and L-R shown for correct assembly of following steps

Étape 7 - Air dump over ride and pressure switch

1 It is vital that the air service unit override switch and air pressure sensor are accessible from the front of the unit.

To correct the position, the unit can easily be rebuilt.

2 Remove top plug by unscrewing cap and pulling plug off. Remove 2 off screws indicated and rotate over ride 180 degrees and refix with screws. Replace Cap and plug

3 Remove 2 off M5 socket caps and dismantle. Rotate pressure switch 180 degrees and reassemble. Ensure O rings shown are correctly seated when rebuilding