| [version en cours de rédaction] | [version en cours de rédaction] |
| (Une révision intermédiaire par le même utilisateur non affichée) | |||
| Ligne 45 : | Ligne 45 : | ||
Pen mark all fasteners to show finalised</translate> | Pen mark all fasteners to show finalised</translate> | ||
|Step_Picture_00=R0015086_Assemble_Pneumatics_on_to_electrical_cabinet_loctite_243.png | |Step_Picture_00=R0015086_Assemble_Pneumatics_on_to_electrical_cabinet_loctite_243.png | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
| Ligne 117 : | Ligne 103 : | ||
{{Tuto Step | {{Tuto Step | ||
|Step_Title=<translate>Mains supply 12mm blue</translate> | |Step_Title=<translate>Mains supply 12mm blue</translate> | ||
| − | |Step_Content=<translate> | + | |Step_Content=<translate>12mm blue pipe runs from cabinet supply to Y near connection for load wheel 6mm. 12mm carries on ready to plug into M/C</translate> |
| − | + | |Step_Picture_00=R0015086_Pneumatic_connections_Screenshot_2023-12-11_095408.png | |
| − | + | |Step_Picture_01=R0015086_Pneumatic_connections_Screenshot_2023-12-11_095414.png | |
| − | + | |Step_Picture_02=R0015086_Pneumatic_connections_Screenshot_2023-12-11_095419.png | |
| + | |Step_Picture_03=R0015086_Pneumatic_connections_Screenshot_2023-12-11_095423.png | ||
| + | |Step_Picture_04=R0015086_Pneumatic_connections_Screenshot_2023-12-11_095429.png | ||
}} | }} | ||
{{Notes}} | {{Notes}} | ||
Version actuelle datée du 11 décembre 2023 à 11:37
Instructions for adding pneumatic circuits to main frame
Difficulté
Moyen
Durée
8 heure(s)
Introduction
Tools Required
Standard spanner set
Standard Hex key set
Pipe Cutters
Part Required
P0000160 Fitting: Flow Controller In Line 6mm x 1
P0001023 Fitting: SMC 6mm mini Y x 2
P0001030 Fitting: SMC 6mm Equal Tee x 16
P0001053 8-6 reducer x 1P0001106 reducer 12-8 x 1
P0001107 12mm Y connector x 1
P0001108 Tee connector 12mm x 2Étape 1 - Unless otherwise stated
Use locktite 243 on all fasteners
Use loctite 572 on all threaded pneumatic connection
Pen mark all fasteners to show finalised
Étape 2 - Y154 Loader Wheel
Pictures please
6mm black air pipe
1542 to base of cylinder runs to out port of regulator on electrical cabinet
1541 connects to nose of cylinder, add P0000160 close to cylinder, then run connection to port 2 on valve bank for Y154 connection
Connect IN port of regulator with 1541 and connect to port 4 on valve bank
6mm blue airpipe
Connect check valve fitting to main blue 12mm feed line using 12- 8 reducer,8-6 reducer and 12mm Y connector
Étape 3 - Y157 Roller beds
Pictures please
1579 Connects from nose of cylinder to port 4 on valve bank
1571 connects to base of cylinder and port 2 of valve bank
Étape 4 - Y375 Blowers
Pictures please
3759 connect to port 2 of pilot valve
Connect to blowers. Must have P0000160 flow regulator fitted close to blower points
Étape 5 - Cabinet Pneumatic connections
pilot valve
Port 1 connected to 12mm ring main
Port 2 3759 connects to blower
Port 12 3759 connected to port 4 on valve bank
Étape 6 - Mains supply 12mm blue
12mm blue pipe runs from cabinet supply to Y near connection for load wheel 6mm. 12mm carries on ready to plug into M/C
Draft
Français
English
Deutsch
Español
Italiano
Português