R0015247 Fit X axis gearbox and Motor

Instructions to mount and set X axis gearbox and motor drive parts

Difficulté

Medium Moyen

Durée

1.5 hour(s) heure(s)

R0015028D_Fit_X_axis_gearbox_and_Motor_Screenshot_2023-06-14_110228.png

Introduction

Tools Required

Feeler gauge set

Standard hex key set

Standard Tap set

Torque wrench (0-50nm)

Extended 4mm hex bit 1/8 drive

Parts Require

D0015073B x 1

C0001212 x 1

H0008301 x 1

C0001122K x 1

D0015290 x 2

M0001087 x 2

Étape 1 - Unless otherwise stated

Use loctite 243 on all fasteners

Use Loctite 572 on all threaded pneumatic connections

Pen mark all fasteners to show finalised

Étape 2 - Check drive

Check fit of drive pinion H0008301 onto gearbox C0001212 . Pinion should be able to move over shaft and key, as adjustment will be required later

Étape 3 - Attach Gearbox mount plate

Attach gearbox mount plate D0015073B as shown to gearbox C0001212

Use 4 off M5 x 25? socket cap to fix

Ensure orientation is as shown and gearbox access hole is in the correct position

Étape 4 - Fit pinion

Attach pinion to gearbox but do not secure

Étape 5 - Mount to carriage plate

Mount to carriage plate as shown using 2 off M8 x 35 socket cap and heavy M8 washer and 2 off M8 x 25 socket cap with heavy M8 washer. Do not apply adhesive at this point and lightly tension fasteners

Étape 6 - Set drive pinion height

Set height of drive pinion in relation to hepco rail V edge .

Gap between these parts should be 0.25mm (0.010")

To set this use feeler gauge

Fix pinion in position with M6 x 10 KCP grubscrew

Étape 7 - Set Gear meshing

The gear meshing will need to be set to the least possible backlash that the v rail will allow , with no over over meshing . To set this the following needs to be done

Start at end of main hepco rail

1 Release tension on gearbox mounting plate fasteners and push in direction shown to put gearbox drive pinion and toothed rail into full mesh . This should only require light finger pressure. Lightly tension 2 off bolts

2 Start to push by hand the complete assembly slowly along the hepco rail in the direction shown . Movement should be smooth and consistent.

High spots on the toothed rail need to be identified , and these will be felt when moving the carriage along the rail , as the pressure required to move will increase. . When the high spot is felt, stop the carriage at the exact position and reset to the gearbox assembly as in step 1, to set the back lash to zero at the newly identified high spot

3 Continue these steps until the end of the rail is reached

Étape 8 - Check back lash between gears

This can be checked by the following

1 Insert hex key into locking fastener as shown and apply sideways pressure to stop the collar rotating

2 Rock the carriage in the directions shown to see how much movement is present with the gearbox 'locked' Movement in this direction should be minimal to none .

3 Repeat this check at several points along the rail to quantify maximum backlash present. Any excessive backlash should be reported to supervisor

4 Add Loctite 243 to 4 off M8 bolts 1 at a time now positioning is complete

Étape 9 - Sign off

Gear back lash setting to be checked by supervisor

Étape 10 - Identify torque setting

1 Inspect indicated face of gearbox and identify Torque setting for gearbox coupling

2 Transfer this data to beside the access hole to allow setting to be known after servo motor has been fitted

Étape 11 - Fit servo motor

1 Servo motor c0001122k will need degreasing before fitting . The spindle of the motor needs ALL grease removing with FE10 solvent before fitting to the gearbox. This is due to the coupling requiring friction to maintain a mechanical coupling

2 Fit servo motor to carriage assembly and orientate as shown . Use 4 off M5 x 16 socket caps to fasten.

Étape 12 - Apply torque

1 Use torque wrench and set at gearbox nominated setting, then set tightness of coupling

2 Fit access hole bung supplied with gearbox

Please take picture to clarify orientation of gearbox and servo

Étape 13 - Add end stops to main drivebeam

1 Attach M0001077 to D0015290 ( 2 off )

2 Use image to identify mounting points on main drive rail and tap relevant holes to M12 x 1.75 pitch (6 off in total)

3 Fix stop brackets as shown with 3 off per stop M12 x 25 socket caps

en none 0 Draft