R0015114 Bench Assemble Valve Banks and Regulators

Assembly details for pneumatic components

Difficulté

Medium Moyen

Durée

1 hour(s) heure(s)

R0015114_Bench_Assemble_Valve_Banks_and_Regulators_Screenshot_2023-10-25_091222.png

Introduction

Tools Required

Standard hex key set

Standard spanner set

Standard HSS drill set

Standard tap set

Parts Required

H0007998 Regulator internal mount 5 way x 1

P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 14

P0000020 Fitting: Plug 1/8" BSP (Grubscrew Type) x 9

P0000021 air gun assembly x 1

P0000024 hex nipple 1/4 x 3

P0000058 Regulator Mounting Kit x 1

P0000074 Elbow Adaptor 8mm - 1/8 BSP (Pneumax not acceptable) x 2

P0000096 Fitting: Brass Reducing Bush 1/2 - 1/4 x 2

P0000142 Elbow Adaptor 8mm - 1/8 BSP x 2

P0000145 tee equal 1/4 x 3

P0000159 Fitting: Stem Blanking Plug 6mm x 2

P0000277 Fitting: Bulkhead Female 8mm x 1/4 BSP x 1

P0000278 Regulator 0-2 bar x 1

P0000332 Regulator with Gauge G1/8'' 0-8 bar x 8

P0000361 1/4'' Male Probe to suit 1/4'' PCL Female coupling x 1

P0000419 Air Service Unit OH (P0283) x 1

P0001071 Valve base type41 8 position x 1

P0001074 Fitting: 1/4" BSP Hex Head Silencer x 4

P0001101 Male straight 1/4 bsp to 12mm x 1

P0001102 Fitting male elbow 12mm 1/4 x 4

P0001105 Bulkhead straight 12mm x 6

P0001186 Valve. 24v dc smc x 8

Étape 1 - Unless otherwise stated

Use Loctite 243 on all fasteners

Use Loctite 572 on all threaded pneumatic connection

Pen mark all fasteners to show finalised

Étape 2 - Ecr raised

Ecr raised to amend regulator bracket to remove redundant holes and add fixing holes for valve bank

Use part as is until process to update is complete

Drill regulator bracket M4 to suit valve base

Étape 3 - Assemble valve bank

Assemble valve bank as shown

Étape 4 - Attach valve bank

Attach valve bank to regulator bracket using M4 socket caps , washers and nyloc nuts

Étape 5 - Assemble regulators

Assemble 7 off regulators with 6mm elbows and spare port blanked

Assemble 1 off regulator with 8mm elbows and spare port blanked

Étape 6 - Assemble Air service unit

Assemble air service unit

Étape 7 - Mount air service unit

Mount air service unit to front lower panel

Étape 8 - Mount regulators

Mount regulators to front lower panel

As viewed from front, bottom right regulator should have 8mm fittings

Étape 9 - Mount bulkheads

Mount 3 off 12mm bulkheads to lower panel

Étape 10 - Assemble and mount 0-2bar regulator

Assemble and mount 0-2 bar regulator to lower front panel

Étape 11 - Fit and connect air gun assembly

Fit 8mm bulkhead to lower front panel

Fit air gun assembly

Connect 8mm red pipe from reg OUT to bulkhead

Étape 12 - Fit cable gland

Fit cable gland for air service unit

Étape 13 - Fit labels for regulators

Print and Attach labels for regulator's

Labels to be added both sides of panel

From top left to bottom right

Y350 Clamp Infeed Top

Y351 Clamp Infeed Side

Y386 Clamp Middle Top

Y386 Clamp middle Side

Y395 Clamp V Top

Y395 clamp V Side

Z Axis Support

VZ Axis Support

Étape 14 - Lower rear panel bulklheads

Fit 3 off 12mm bulkheads to rear lower panel

Étape 15 - Label bulkheads

Print and fit Labels to identify bullheads as

12mm red 2 off

12mm blue 1 off

en none 0 Draft