Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.
Liste de résultats
- # Within BCP choose "Parameter Settings" # Select the LAN tab # Enable TCP/IP # Enable Wired LAN # Set IP Address and Sub Net Mask # Press the Set Parameter at the bottom. <br/> +
- 1) Pressing "Feed" should push out another … 1) Pressing "Feed" should push out another label regardless. 2) Send a label to the printer via the network (or via the Test - Send file within BCP). 3) Send more than one file and make sure that each time you remove a label from the output the next one is presented.from the output the next one is presented. +
- <div class="icon-instructions info-icon"> <div class="icon-instructions-icon"><i class="fa fa-info-circle"></i></div> <div class="icon-instructions-text">...This is often necessary to make sure the printer returns in emulation mode properly</div> </div> +
- Ensure that the sensor head is in the middle of the label +
- Ensure the switch is set to REWINDER +
- For easy setup use a USB cable (Alternativ … For easy setup use a USB cable (Alternatively everything can be done via the network web interface) 1) Connect a USB cable to the PC 2) Connect a Network cable to a live DHCP network to obtain an IP address. 3) Download and install the BCP setup software: [https://url6.mailanyone.net/scanner?m=1pIYAE-0003U9-3G&d=4%7Cmail%2F90%2F1674147000%2F1pIYAE-0003U9-3G%7Cin6f%7C57e1b682%7C27359798%7C12301058%7C63C975823F8CF099951D682ADAAD7EC2&o=%2Fphtw%3A%2Fwtsbow.thiatsdcecwm%2Fo.ovanlr_oeodissetprna%2Fisergttn%2FeCo_t_%2FBPol%2FseireS&s=uO4_tHdOp9-EM4-X9--MGgLUV_Y https://www.toshibatec.com/download_overseas/printer/setting_tool/BCP_Series/] [https://url6.mailanyone.net/scanner?m=1pIYAE-0003U9-3G&d=4%7Cmail%2F90%2F1674147000%2F1pIYAE-0003U9-3G%7Cin6f%7C57e1b682%7C27359798%7C12301058%7C63C975823F8CF099951D682ADAAD7EC2&o=%2Fphtw%3A%2Fwtsbow.thiatsdcecwm%2Fo.ovanlr_oeodissetprna%2Fisergttn%2FeCo_t_%2FBPol%2FseireS&s=uO4_tHdOp9-EM4-X9--MGgLUV_Y]ergttn%2FeCo_t_%2FBPol%2FseireS&s=uO4_tHdOp9-EM4-X9--MGgLUV_Y] +
- If the labels have been fitted properly on power up the calibration process will eject several labels. Take a note of the IP address given to the printer on the front panel. +
- Press the Emulation Button and take the to … Press the Emulation Button and take the top option "Zmode System Parameter Settings"
Then Make the changes
*Label Length '''38mm''' (after calibration this will be reset to 41.3)
*Label Width '''98mm'''
*Ribbon '''WITHOUT RIBBON'''
*Print mode '''PEEL OFF'''
*Sensor '''TRANS PREPRINT'''
*Max Label Length (for calibration) '''200mm''' (this just saves on labels)
Press the '''DOWNLOAD''' button and check that there are no errors.
Now on the Toshiba side:
*Select Paraeter Settings
*Select Standard 2 (General 2 on BCP TOOL)
*Adjust Cut Adjust to -2.0
*Press the submit button
The screen shows the Web version. The adjustment brings the label forward out of the printer to allow collection by the Picking Arm.
low collection by the Picking Arm. <br/> + - The instructions for both the Inner & Outer wound labels are on the inside of the open lid. <br/> +
- There will be no ribbon and as the settings will be for Peel Off a length of blank backing needs to be fed onto the Rewind spool +
- To gain access turn the green knob to FREE. You can then pull the front plate down and lift the printer head up. +
- When loaded close the Printhead down, lift the front plate up and turn the green knob to LABEL. +
- When you start BCP you should see as picture Select USB if not Selected +
- With the Printhead open ensure that the labels are under the small black sprung guides. Slide the green guide to the width of the label. +
Français
English
Deutsch
Español
Italiano
Português