Rechercher dans les propriétés de la page

Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.

Liste de résultats

• 1 Ensure all 16 off fasteners are slight … 1 Ensure all 16 off fasteners are slightly loose to allow plate to align correctly 2 Add light pressure to all 16 off fasteners , move plate up and down to check free running with consistent pressure required 3 Remove each individual fastener and add loctite 243, and apply final tension 4 Double check correct operation of plate up and downeck correct operation of plate up and down  +
• 1 Use 4 off M8 x 30 and 2 off M8 x 35 to fix blocks 2 Adjust both blocks to be level on indicated face 3 Fit M8 x 12 Kcp grubscrew 2 off 4 Finalise shaft grubscrews 2 off  +
• 1 Fit first flange to spindle and fit saw blade . Ensure blade is orientated correctly 2 Fit front flange, and locking bolt and washer. Apply medium Tension with 24mm spanner and blade flange spanner  +
• 1 Fit motor plate to upstroke plate , Comb … 1 Fit motor plate to upstroke plate , Combining part D0015491 saw turntable flag bracket and using D0004157 motor plate spacers between upstroke plate and motor plate . Use 2 off M8 x 50 socket caps, 1 off M8 x 40 socket cap and 3 off M8 motor plate washers
  
  ...Ensure motor is fixed at the top of slot adjustment as shown and fitted parallel and level
  2 Attach Sr datum flag as shown using 2 off M6 x 20 socket caps and M6 A form washersdiv> 2 Attach Sr datum flag as shown using 2 off M6 x 20 socket caps and M6 A form washers  +
• 1 Slide off taper lock pully from spindle … 1 Slide off taper lock pully from spindle assembly and remove flanges and bolt for saw blade 2 Position spindle into plate as shown . Use countersunk bolt as reference for alignment . Use M8 x 30 socket cap to help align mounting holes when fitted .
  
  ...Countersunk bolts on spindle assembly may impede fitting into plate. If required, countersunk bolts can be dressed with a file to achieve clearance
  3 Check clearance on washer shown. If washer interferes with spindle, remove washer 4 Remove 1 off locating M8 socket cap. Add 4 off M8 x 30 socket caps and A form washers and finalise 5 Refit taper lock pulley to spindle assembly
  et caps and A form washers and finalise 5 Refit taper lock pulley to spindle assembly <br/>  +
• <div class="icon-instructions caution-i …
  ...Ensure bearing seals are not damaged during the fitting of the upstroke plate assembly. Ensure bearings are aligned correctly
  1 Position 1st set of bearings over shafts 2 Position shaft tie blocks over shafts as shown 3 Lower and align top set of bearings 2 Position shaft tie blocks over shafts as shown 3 Lower and align top set of bearings  +
• All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added  +
• Clean shafts with FE10 solvent Fit shafts to turntable plate using M8 x 12 KCP grubscrews , do not add final tension or adhesive at this point  +
• Fit web using 6 of M8 x 25 socket caps Use to set pitch of brace supports, Tension dowelled upright side first Adjust to set indicated faces flush Finalise fasteners on brace supports and web  +
• Motor plate must be fitted int he slot position shown in the next step to allow correct rotation of the saw head  +
• attach brace supports to turntable plate … attach brace supports to turntable plate '''Do not tension brace 2 , add adhesive ready for next step''' Orientate as shown
  ...Ensure indicated faces are set flush
  Use M8 x 35 Socket caps and A form washers . Use 2 off 8mm x 24mm dowels in brace support 1 that aligns with dowel holes in turntable base . Use 2 off 8mm x 24mm dowels in brace support 1 that aligns with dowel holes in turntable base  +