Rechercher dans les propriétés de la page

Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.

Liste de résultats

• 1 Fit D0015235 VY Datum Switch Bracket … 1 Fit D0015235 VY Datum Switch Bracket as shown along with D0015251 Safe Sensor Finger Note. This assembly always fits to the rear of the v notch assembly (for handing orientation ) 2 Set E0000336 sensor as shown. Set to minus 1mm to face of bearing rail Ensure locking nut for sensor is not over tightened as damage can be caused to sensorightened as damage can be caused to sensor  +
• 1 Attach as shown 4 off D0015161 Saw Plate , using 2 off M10 x 30 socket caps and A form washers to fix 2 Ensure indicated faces are set flush  +
• 1 Attach 4 off pre build motor supports. Orientate as shown 2 Fix using 4 off M10 x 40 socket caps and A form washers, and 4 off 8mm x 50 hardened dowels per saw plate  +
• 1 Attach 4 off pre build motor supports. O … 1 Attach 4 off pre build motor supports. Orientate as shown 2 Fix using 4 off M10 x 40 socket caps and A form washers, and 4 off 8mm x 50 hardened dowels per saw plate 3 Fit 4 off E0001185 Elte Saw motor as shown using 4 off M10 x 50 socket countersunk bolts per motor 4 Ensure motor is set level using engineers level on the indicated axis as shown when fitting motorsndicated axis as shown when fitting motors  +
• 1 Fit 2 off D0015183 VY Stop as shown. Fix with M8x 30 socket caps and A form washers and orientate as shown 2 Fit M10 x 50 set bolt and M10 nut as indicated. 3 Set position. Adjust hard stop to achieve indicated position  +
• 1 Thoroughly degrease B0000046 Slide Base … 1 Thoroughly degrease B0000046 Slide Base Bearing Block fixing holes with FE10 solvent 2 Fit bearings to rails as shown. Ensure bearing datum face in orientated as shown 3 Slide Bearing to end of rails and fit supplied grease nipple and orientate as shownplied grease nipple and orientate as shown  +
• 1 Use 2 off M12 x 20 socket caps with M12 … 1 Use 2 off M12 x 20 socket caps with M12 A form washers and fix where shown 2 Fit lower brackets with 4 off M10 x 60 socket caps 3 Attach P0001142 Adjustable Damper 150mm stroke 1 off. Fix with 2 off M8 x 40 socket caps and A form washers to Suit to position damper central . Bolt will also require cutting to ensure correct spacing ( See Scott) (Pictures and info required )See Scott) (Pictures and info required )  +
• <nowiki>Photos required of these ste … Photos required of these steps please
  
  
  1 Fit 2 off P0001134 Floating Joint M18x1.5 to 2 off P0001133 Cylinder: Ø50 x 500
  
  
  2 1 off cylinder fit P0001141 Fitting: SMC Flow Controller Elbow Ø8-1/4BSP to nose port , and 1 off P0001140 Pilot Check Valve: 8mm to 1/4" BSP to base port. Fit additional air fitting to check valve (P0000010?)
  
  
  3 1 off cylinder fit P0000026 Silencer 1/4 BSP to nose port, and assemble the following components and fit to base port
  
  
  P0000010 1/8 bsp 6mm elbow x 1
  
  P0000050 Fitting: Silencer 1/8'' BSP x 1
  
  P0000077 Straight Adaptor 8mm - 1/8BSP x 1
  
  P0000140 Fitting: Quick Exhaust Valve 1/8" x 1
  
  P0000022 Fitting: Brass Reducing Bush 1/4 - 1/8 BSP x 1
  
  P0000023 Fitting: Hex Nipple 1/8 BSP x 1<br /><br />P0000022 Fitting: Brass Reducing Bush 1/4 - 1/8 BSP x 1<br /><br />P0000023 Fitting: Hex Nipple 1/8 BSP x 1</nowiki>  +
• Attach 2 off D0015156 Saw Bearing Plate as … Attach 2 off D0015156 Saw Bearing Plate as shown, using fixings indicated Observe following points 1 Ensure bearings are mated correctly to register on bearing block as shown 2 Use bearing plate with correctly mounted bearings to set position on lower bearing rail. Ensure rail position is set by bearing rail at both ends of travel 3 Finalise all Fasteners in lower bearing rail , adding adhesive and tension individually 4 Insert 28 off B0000173 blanking plug to linear rails. Ensure plugs are fitted accurately flush to top face of railitted accurately flush to top face of rail  +
• Attach 2 off P00001144 mounting band, 2 off P0001041 reed switch to cylinder with flow regulation fitted  +
• Attach assembly as shown Secure using 4 … Attach assembly as shown Secure using 4 off M8 x 30 socket caps With A form washers at point A Secure Point B with 2 off M8 x 25 socket caps and A form washers Correct alignment Check . Alignment between leadscrew nut and mounting block are vital. To check alignment , remove fasteners holding leadscrew nut in place, and wind out nut from housing . Check in multiple positions on axis that leadscrew nut enters block correctly and is inline with the borelock correctly and is inline with the bore  +
• Fit 4 off B0000426 Linear Rail MSB25 400mm … Fit 4 off B0000426 Linear Rail MSB25 400mm Long as shown A and B can be finalised with fixings, C and D should be left loose for adjustment later Use M6 x 20 and M6 x 16 socket caps at indicated points Take care on the following notes as shown 1 Ensure correct witness faces are used 2 Correct fasteners are used at correct positionsct fasteners are used at correct positions  +
• Fit D0015162 Saw Mid Spacer Bar x 1 and D0015163 Saw Bearing Spacer Bar as shown Ensure Datum faces are contacting as shown on both bars  +
• Photos required 1 Attach 2 off D0015168B … Photos required 1 Attach 2 off D0015168B Balance Cylinder Bracket x 2 as shown. Fix with 8 off M8 x 30 socket caps. 2 Attach cylinders to brackets using 8 off M8 x 30 socket caps and A form washers Cylinder with flow restrictors to be fitted to front of machine, cylinder with quick exhaust to be fitted to rear of machine. 3 Use P0000401 to connect to cylinder check valve and purge to disable check lock and allow movement 4 Attach cylinders to top mounts (pictures required) 5 Connect air to cylinders to lift V notch assembly to maximum up position 6 Adjust cylinder stroke into floating knuckle and floating knuckle into mount block to achieve measurement indicated of 59mm. Set both sides to this measurement . Ensure thread is evenly distributed between both components when adjusting (photo required)omponents when adjusting (photo required)  +
• Pictures required Assemble 2 off M000108 … Pictures required Assemble 2 off M0001087 Rubber Bump Stop M6 Ø20x24 with D0015440 Spacer: Ø12.7 x 36, M6 tap thru adding M6 nut for locking With v notch assembly lowered, Fit assembled bump stops to positions shown Attach with M6 x 35 socket caps and M6 heavy washer Set to shown measurement of 65mm washer Set to shown measurement of 65mm  +
• Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised  +