Rechercher dans les propriétés de la page

Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.

Liste de résultats

• 1 Check all levels again after adjusting rollers A and B 2 Use 2 meter straight edge and feeler gauges to check alignment of rollers and cut table Adhere to tolerance of - 0.002"  +
• 1 Level On X axis using engineers level a … 1 Level On X axis using engineers level and adjusting grubscrews in indicated areas 2 Level from Rollers at indicated point. Adjust previous level points evenly to adjust level reading on rollers 3 Remove Middle roller and top blower 4 Use 300mm parallels to span rollers and engineers level to check and adjust Y axis level of rollerso check and adjust Y axis level of rollers  +
• 1 Remove roller from clamp C as shown 2 Use 2 meter straight edge as shown, pushed against roller A and C 3 Ensure Rollers B are moved away from straight edge <br/>  +
• 1 Use 1 meter straight edge as shown, and hold in position against z axis support blocks 2 Check as shown with engineers square to asses squareness of sub frame to clamps  +
• 1 Use a 2 meter straight edge to span between rollers A and B 2 Use engineers level on straight edge to identify if either A or B is the low point 3 Raise A or B to bring level  +
• 1 Level Y axis with engineers level and 300mm parallels. 2 Adjust using M8 flat bottom jacking grubscrews 3 Check and adjust X axis level  +
• Cut tables must be fitted during this alignment. This will ensure cut tables are accurately set and and any dicrepancies will be identified at this stage . Please ensure all tolerances of maximum 0.002"/0.05 mm is adhered to all times on set up  +
• Datum C now requires roller refitting and … Datum C now requires roller refitting and repositioning 1 Refit roller 2 Slacken 2 off M6 fasteners that hold Roller assembly C in place 3 Ensure straight edge is firmly against roller assemblies A and B 4 Position and Tighten Roller assembly C to align with 2 meter straight edge 5 Check with 0.002" feeler gauge that all rollers are aligned and in tolerancet all rollers are aligned and in tolerance  +
• Datum rollers B can now be aligned using A and C as the Datum With the 2 meter straight edge against A and C, adjust B to alignment is achieved on back fences Check with 0.002" feeler gauge on all rollers when setting  +
• Ensure once set, all levels and alignment covered in this procedure, as double checked and confirmed as correct Supervisor sign off required  +
• Front Bar indicated requires doweling in p … Front Bar indicated requires doweling in position 1 Drill 9.5mm to a depth of 25mm into steel support tab at the 2 indicated points 2 Open holes to 10mm diameter 3 Insert 2 off 10mm x 60mm spiral pins to fix position . Ensure dowel is sitting equally between clamp bar and steel supportqually between clamp bar and steel support  +
• Once dowelling and sign off is complete, remove roller and blower from datum A should be refitted and fasteners finalised .  +
• Recheck all levels and alignment of rollers in all aspects once squareness setting has been performed. These settings are possible to change after front bar has been adjusted  +
• Span from roller A to B with 2 meter straight edge Identify if roller C is high or low If high, increase height of rollers A and B and re set levels If low, follow next step for subframe adjustment  +
• Squareness must be rechecked once Datum rollers B have been aligned , using the same check as step 9  +
• Squareness of datum faces to sub frame must be set with no tolerance. Perfect squareness should be achieved  +
• This step is required is centre rollers C require lifting 1 Release lock nut on plate 2 off 2 Release M8 grubscrew 2 off 3 Release M12 socket caps 4 off 4 Adjust in equal turns M10 jacking grubscrews Re level and tighten subframe  +
• To adjust squareness, indicated bar must be adjusted Always ensure when adjusting that the following is observed <br/> * Indicated bar must not protrude Exterior face of main frame * One side of bar must always remain flush with main frame  +
• Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised  +