Rechercher dans les propriétés de la page

Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.

Liste de résultats

• 1 Attach cylinder to beam using M8 x 25 socket caps and 4 off F0000315 M8 D- nuts 2 Tension bolts to hold indicated bracket in a vertical position 3 Apply holding tension to these fasteners 1 and 2  +
• 1 Mount D0015074 2 off brackets using 8 off M8 x 50 socket caps and M8 a form washers , orientating cylinder as shown 2 Mount D0015077 to cylinder using 4 off M8 x 30 socket caps  +
• 1 Move hepco beam to extended position as shown 2 Apply holding tension to same bolts as other mounting bracket  +
• 1 Mount sensor brackets D0015144 with … 1 Mount sensor brackets D0015144 with M6 x 16 socket caps x 2 and heavy M6 washers 2 Fit E0000336 sensor and Adjust bracket using slots to set sensor to edge of block when at full travel 3 Ensure sensor is set as close as possible to reading face 4 Repeat for other sideto reading face 4 Repeat for other side  +
• 1 off of each per side 1 Use 2 off M16 x 80 set bolts and standard M16 nuts 2 P0000109 damper x 2 Do not fully wind in either parts  +
• Add 4 off 8mm x 24mm dowels to parts D0015708 as shown  +
• All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added  +
• Assemble D0015077b with contains D0015707 x 1 and D0015708 x 2 using M8 x 30 socket caps 4 off  +
• Attach 4 off D0015075 to frame using M8 x 25 bolts and Heavy M8 washers as shown Do not apply adhesive  +
• Check that cylinder is positioned as shown  +
• Ensure hepco rail is still at correct datum position of 895mm  +
• Fit 2 off P0001145 air fittings to cylinder P0001118  +
• Lightly attach cylinder assembly to frame , orientated as shown. Use 16 off M8 x 25 socket caps with heavy M8 washers Do not apply adhesive  +
• Move beam to full cylinder extension in on … Move beam to full cylinder extension in one direction. 1 Linisher flat end of set bolt and adjust M16 set bolt to touch face of cylinder mount when in this fully extended position 2 Move beam away from bolt and rotate an EXACT 3/4 turn clockwise at the hex head to set stop position and lock off with m16 nut 3 Repeat for opposite end set bolt, moving cylinder stroke to the opposite end of travelinder stroke to the opposite end of travel  +
• Once alignment has been achieved, 32 off M8 socket caps will need to be individually removed , adhesive applied and finalised .  +
• Quality check movement of beam from positi … Quality check movement of beam from position 1 to 2 Movement must be free and consistent over the entire stroke of the cylinder 1 If not alignment must be rechecked by adjusting mounting brackets to obtain smooth running 2 Once Movement is free running , secondary check alignment by removing tension of fasteners holding cylinder mount block to hepco beam 3 Check that slight movement is possible between the hepco rail and the mounting block. Block should not move away from hepco rail when un fastened or be held against under pressure. If either of these happen it indicates mis alignment between components , and step 1 should be repeated 4 Tension m8 socket caps and apply final tensionion m8 socket caps and apply final tension  +
• Set damper position by moving cylinder to full stroke, and adjusting damper so a gap of 5mm is left at the indicated point Lock off damper lock nut Repeat for both sides  +
• To check correct setting of stroke length, … To check correct setting of stroke length, a measurement should be taken to confirm. To do this do the following steps. 1 Move cylinder to one position against set hard stop 2 Measure between Hex bolt thread end and cylinder anchor as shown 3 Confirm measurement is between the range of 696-698mm. Any measurement outside of this tolerance requires resetting of hard stops correctlyrequires resetting of hard stops correctly  +
• once all above steps have been followed, Guard D0015948 can be fitted Pics and fastener sizes required  +