Rechercher dans les propriétés de la page

Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.

Liste de résultats

• '''<u>Cylinder assemblies with HEX S … '''Cylinder assemblies with HEX SET bolts must be used on these 3 off small roller tables''' 3 off Using same checks and setting as above assemble 2 off roller tables with 4 rollers as shown, Use the pre built cylinder bracket with m3 tapped holes for 1 off, and add 1 off Sensor E001120 ,1 off Blower P0000200 and 1 off bracket D0015547 as shown. Identify pipe as 2399 and fit P0000160 flow regulator to pipey pipe as 2399 and fit P0000160 flow regulator to pipe  +
• 1 D0015006B indicated holes should measure … 1 D0015006B indicated holes should measure as shown. Rework by hand if issued old spec ECR raised 06/06/23 2 D0015002 rod end shaft . Check fit in P0000049 spherical bearing . Polish down diameter to allow shaft to pass through. ECR raised 06/06.23 to improve tolerance of shaft to allow better fitmenttolerance of shaft to allow better fitment  +
• 1 Tap 2 off indicated holes M3  +
• 1 off Attach 2 off D0015283 backfence to roller assembly using M6 x 16 socket caps, A form washers and M6 nyloc nut  +
• 14 off 1 Fit 2 off D0015010 spacers, 1 off d0015002 shaft through spherical bearing and fix with 2 off m6 X 12 socket caps and A form washers 2 Fit 1 0ff D0015603 pivot shaft with 2 off M6 x 12 socket caps and A Form washers  +
• 14 off 1 Combine D0015481 shaft and B0001 … 14 off 1 Combine D0015481 shaft and B0001220 spacer as shown to mount cylinder to bracket. Use M6 x 12 socket caps and A form washers to fasten on 11 off cylinder mounts. Use M6 x 12 hex set bolts with no washers on 3 off cylinder mounts 2 Fit 2 off B0001103 bushes to D0015006B 2 Fit 2 off B0001103 bushes to D0015006B  +
• 14 off Check part D00150001 has been supplied to new specification Check indicated hole, should measure 8.2mm. If not open up with hand drill Drawing change requested 06/06/23 to amend from 8mm to 8.2mm  +
• 3 off Attach 1 off D0015283 backfence to roller assembly using M6 x 16 socket caps, A form washers and M6 nyloc nut  +
• 5 off Attach D0015069 backfence to roller assembly using M6 x 16 socket caps, A form washers and M6 nyloc nut  +
• 5 off 7 Roller bed assemblies with two cylinders require pneumatic pipe installation. Use identification numbers as follows 1461 Home position 1469 Active position (down)  +
• 5 off to be assembled Use cylinder brack … 5 off to be assembled Use cylinder bracket assemblies with Socket cap heads 1 Mount 2 off D0015005 to prebuild cylinder assemblies as shown Use M6 x 20 button socket , A form washer and M6 nyloc nuts to fix. Do not use washer under head of button head screw, on use on on nut side 2 Adjust the 2 off D0015005 1st section pushed against edge of clearance hole in direction shown 2nd section pushed in same direction 3rd Check parallel and adjust to correct 4th check squareness by taking corner measurements and adjusting if required Once all above is achieved, finalise fasteners all above is achieved, finalise fasteners  +
• <div class="icon-instructions caution-i …
  ...Ensure Fixing nut from indicated point is removed from each cylinder and disregarded
  14 off
  ...All Flow regulator fittings P0001198 should be set at this point to the correct flow rate. To do this follow these steps 1 Wind regulation screw clockwise until fully in. Do not overtighten, stop when light resistance is felt. 2 Turn regulation screw exactly 2.5 turns anticlockwise to set flow rate
  1 Fit 2 off P0001198 fittings to cylinder P0001110 2 Fit spherical bearing P0000049 to cylinder end , Do not add final tension to the nut1 Fit 2 off P0001198 fittings to cylinder P0001110 2 Fit spherical bearing P0000049 to cylinder end , Do not add final tension to the nut  +
• D0015283 Saw Infeed Backfence Plate x 5 and D0015608 Saw Infeed Backfence Plate (Full Length) x 5 should be supplied from manufacturer free from burrs and sharp edges Please check these parts are correct, if sharp edges are present please report  +
• Ensure cylinder assemblies with socket caps fitted are used on these assemblies Using same checks and setting as above assemble 1 off roller table with 4 rollers as shown  +
• Fit 7 off B0001092 roller to each assembly  +
• Please be aware following step has been amended to include new assembly details. It is now required to assemble 3 off of the 14 off cylinder mounts differently Amendment to fastener type used  +
• Please ensure correct assembled cylinder mounts are fitted to the correct assemblies  +
• Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised  +