Rechercher dans les propriétés de la page

Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.

Liste de résultats

• 1 Attach 2 off P0001198 Fitting: flow co … 1 Attach 2 off P0001198 Fitting: flow control 1/8 x 6mm elbow to cylinder P0000484 Cylinder 32 x 100 stroke 2 Attach cylinder to assembly using M6 x 40 socket caps and M6 A form washers (do not tension yet ) Find in cylinder piston to leave 2 threads exposed when lock nut is tightened 3 Push cylinder assembly to closed position (shown) and apply tension to M6 fixings Finalise all bolts and nuts 4 Check alignment . Cylinder stroke should be even and smooth at all points of travel . There should be no tight spots, especially at the end points of cylinder travelially at the end points of cylinder travel  +
• 1 D0001331 Roller Ø40 x 27 c/w bearing and D0003788 Z Roller Pin (40mm) 2 D0001334 Roller Ø40 x 102 c/w bearing and D0003108 Shaft 20mm: 146mm Clamp Roller Shaft  +
• 1 Dry fit H0007773 Shaft 25mm: 268mm ZX Infeed Clamp Top x 2 using M6 x 10 KCP grubscrews 2 Fit to assembly , taking care to ensure bearing seals are not damaged when inserting shafts  +
• 1 Use loctite 243 on cylinder fixing nut … 1 Use loctite 243 on cylinder fixing nut 2 D0015428 Top Clamp Block Ø30 15
  ...Taken extra care to ensure this block and lock nut are correctly tensioned and adhesive 243 applied
  3 Fit M0000253 anti slip pad 22mm to indicated face 4 Fit P0000007 Straight Adaptor 6mm - 1/8 BSP tapered thread x 1 and P0000010 elbow 6mm 1/8 fitting x 1 to ports shownr 6mm - 1/8 BSP tapered thread x 1 and P0000010 elbow 6mm 1/8 fitting x 1 to ports shown  +
• <div class="icon-instructions info-icon …
  .....only follow this step is bearing/shaft fit is loose. Use these generic steps for assembly of issued rollers
  Thoroughly degrease all parts with FE10 solvent 1 Fit 20mm external circlip to shaft 2 Fit roller to shaft 3 Add 3 drops of Loctite 641 bearing retainer to indicated area and smear around the shaft 4 Move shaft to shown position and add 3 more drops of bearing fit to indicated face and smear around 5 Position roller against circlip and remove any excess bearing fit with rag 6 Leave roller in a vertical position to allow bearing fit to cures bearing fit with rag 6 Leave roller in a vertical position to allow bearing fit to cure  +
• <u>'''Vital for correct operation of … '''Vital for correct operation of clamp hold assembly''' Rubber pad must also be fitted Ensure when fitting profile stop assembly as shown, that the indicated part sits above the rollers as shown. The bottom of the rubber pad must be above the height of the rollers as shown Please speak t supervisor if this setting is not possiblease speak t supervisor if this setting is not possible  +
• Attach 3 off low rollers to z plate with M6 x 20 socket counter sunk fasteners Ensure B0001176 Washer :bearing shim x 3 are positioned between each roller and z plate  +
• Attach cylinder stop to main assembly as shown using 2 off M8 x 50 socket caps and a form washers . Set to middle slot position  +
• Attach pre built roller and shafts to D0007774 Top Roller Block using 2 off M6 x 10 KCP grubscrews  +
• Check fit of following parts . Shafts sh … Check fit of following parts . Shafts should pass through bearings with only slight resistance . All inner bearing faces should have contact to shaft and rotate when the shaft is turned If shafts are tight check drawing and inspect size of shaft . If shaft slides through easily, then follow step 4 slides through easily, then follow step 4  +
• Cylinder stroke must be smooth and consist … Cylinder stroke must be smooth and consistent over full travel of cylinder . When rollers are lifted up, they should drop under their own weight to the lowest position. Once alignment has been achieved, all fasteners should be individually removed and apply Loctite 243 and finalisedemoved and apply Loctite 243 and finalised  +
• Dry fit D0000209 Shaft Strap (D8709) using 2 off M6 x 25 socket caps  +
• Fit 2 0ff P00001198 air fittings to cylind … Fit 2 0ff P00001198 air fittings to cylinder Fit P0001160 cylinder 32 x 100 stroke in the orientation as shown Finalise lock nut onto cylinder extension ,leaving two threads of cylinder thread exposed under lock nut. The access nut, release fixings for one shaft, slide upwards to create access to cylinder lock nut.
  
  ...It is important that this cylinder lock nut is tight and has Loctite 243 applied
  Dry fit cylinder to Shaft strap with 2 off M6 x 25 and 2 off M6 x 30 socket caps
  v> Dry fit cylinder to Shaft strap with 2 off M6 x 25 and 2 off M6 x 30 socket caps <br/>  +
• Fit 8 off B0000070 bearings to D0007680 In … Fit 8 off B0000070 bearings to D0007680 Infeed Rail and D0007792 Z Roller Block (D8711) as shown Ensure yellow part of bearing is always facing outside edge when fitted Thoroughly grease bearings with M0000494 lubricant once fitted, ensuring all ball chambers are filled with greaseg all ball chambers are filled with grease  +
• Fit D0000211 Cylinder Extension x 1 to hole shown . Finalise tension  +
• Fit H0007791 Shaft 25mm :250mm ZX Infeed side x 2 as shown . Use 2 off M8 x 12 K.C.P grubscrew to secure  +
• Slide on D0007792 Z Roller Block taken care not to damage bearing seals  +
• Use 4 off M6 x 16 socket caps and A form w … Use 4 off M6 x 16 socket caps and A form washers to fit D0007793 Z Roller Plate
  ...Ensure recess is positioned correctly against indicated face
  
  Ensure recess is positioned correctly against indicated face</div> </div><br/>  +
• Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised  +