Rechercher dans les propriétés de la page

Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.

Liste de résultats

• 1 Fit D0015240 Collar Clamp to leadscrew … 1 Fit D0015240 Collar Clamp to leadscrew as shown 2 Fit C0001005 Stepper Motor AS1050 as shown. One side will fit to stepper motor, Ensure orientation the correct way 3 Secure stepper motor with 4 of M4 x 12 socket caps 4 Check Coupling is not in contact with housing wall Apply adhesive to coupling fasteners and tighten to maximum
  
  ...There must be no force required in the direction shown when fitting these components. If force is required investigate to identify cause
  5 Fit D0015316 Leadscrew Bearing Block Cover with M4 x 10 countersunk boltsiv> </div> 5 Fit D0015316 Leadscrew Bearing Block Cover with M4 x 10 countersunk bolts  +
• 1 Degrease B0000046 Slide Base Bearing Bl … 1 Degrease B0000046 Slide Base Bearing Block with Fe10. Fit 4 off B0001060 Grease Fitting M6x0.75 2 Fit 2 off B0000044 Linear Rail to D0015172 Centralise Plate as shown. Use M6 x 16 socket caps , do not apply final tension or adhesive 3 Fit 4 off B0000046 Slide Base Bearing Block as shown 4 Fit 2 off D0015175 Saw Saddle Carriage Block, Use M6 x 12 socket caps. Apply final tension and adhesive to these bolts 5 Fit roller assemblies and fix with M6 x 16 socket caps and A form washersith M6 x 16 socket caps and A form washers  +
• 1 Assemble tie bases onto D0015175 Saw Sad … 1 Assemble tie bases onto D0015175 Saw Saddle Carriage Block as shown Drill and tap M4 and fit m4 cable tie bases and secure with M4 x 6 button head as shown 2 Add fixing point for datum sensor as shown 3 Rework M0001209 Bracket m8 proximity sensor 90 degree as shown to add 8mm diameter hole0 degree as shown to add 8mm diameter hole  +
• 1 Degrease components D0015208 Leadscrew B … 1 Degrease components D0015208 Leadscrew Bearing Block, D0015207 Outer Bearing Housing and 2 off B0001123 Double angular contact bearings 2 Attach B0001185 Leadscrew nut Igus to D0015209 Leadscrew Attachment Bracket and use 6 off M4 x 20 socket caps and A form washers to fix as shown 3 Check fitment of D0015777 Leadscrew SY as shown. Leadscrew should turn through nut with very little resistance 4 Observe correct bearing fit and use loctite 641 . insert B0001123 Double angular contact bearings into D0015208 Leadscrew Bearing Block and D0015207 Outer Bearing Housing 5 Combine assembled parts as shownsing 5 Combine assembled parts as shown  +
• 1 Fit 6 off D0005186 Guide Pin Washer to H0005185 Shaft 12mm: 90.5 Saw Fence Roller Pin Hold shaft in vice and use M5 x 12 socket cap to secure washer to end of shaft . Finalise bolt Repeat for all 6 shafts/washers 2 Fit Rollers to shafts  +
• 1 Possible Adjustment directions are shown … 1 Possible Adjustment directions are shown using clearance it the counterbored linear rail holes 2 Alignment requirement 3 Starting position for alignment, ensure roller fence blocks are pushed against centralise plate 4 Adjust linear rails to enable both front fence rollers to be aligned correctly 5 Tolerance of 0.002"/0.05mm to be adhered to. Any discrepancy report to supervisor 6 Finalise M6 x 16 socket caps that hold the position of the B0000044 Linear Rail 7 Add 10 off B0000173 blanking caps to finalise rails. Ensure caps are fitted flush to rail. Bearing rails can be removed to allow access to covers caps to be fitted. Take care when re fitting bearings onto railse care when re fitting bearings onto rails  +
• 1 insert shaft into bore following previou … 1 insert shaft into bore following previous step information 2 Insert 0.125mm/0.005" shim between roller and backfence at indicated point 3 Apply very light hand pressure to area shown to position shaft correctly 4 Fit and finalise M6 x 10 kcp grubscrew to secure shaft 5 Remove shim, as only very light hand pressure has been used, this will mean the shim can be extracted without the need to release pressure on the M5 socket cap holding the roller in position Repeat for all 6 rollersler in position Repeat for all 6 rollers  +
• <div class="icon-instructions caution-i …
  ...Ensure perfect alignment is achieve when assembly is mounted . Travel should be free and consistent at all points of leadscrew movement
  Mount leadscrew assembly as shown to centralise plate Use 1 2 off M8 x 70 socket caps 2 2 off M6 x 50 socket caps 3 2 off M6 x 16 socket caps off M8 x 70 socket caps 2 2 off M6 x 50 socket caps 3 2 off M6 x 16 socket caps  +
• <div class="icon-instructions info-icon …
  ...Upgrade R0019222 may be issued with machine . Check with supervisor if required on build . All steps will be listed as optional for this upgrade within this dokit
  Fit 8 off B0000416 Bearings to 4 off D0010357 backfence rollers. Ensure bearings are pushed to shoulder within rollers Fit 4 off D00110358 roller pin to assembled rollers, ensuring fitting pin does not change position of fitted bearingspin to assembled rollers, ensuring fitting pin does not change position of fitted bearings  +
• All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added  +
• Assemble 6 off D0005184 Guide Roller Each … Assemble 6 off D0005184 Guide Roller Each roller has 2 off B0000245 Needle Bearing fitted Ensure bearings are fitted correct orientation . Writing on edge of bearing should be face outwards Use bearing dolly and push bearing down to should within roller body Apply liberal grease to all bearings within rollerseral grease to all bearings within rollers  +
• Assemble optional rollers onto supplied roller housings Ensure M6 A form washer is fitted to small rollers as shown Secure shafts with M6 x 6 pointed grubscrews  +
• D0015172 Check for rework. Add if not present  +
• Dimples in H0005185 Shaft are not used in this application. When fitting shaft , position dimple 180 degrees opposing M6 fixing point in backfence  +
• ECRs raised to cover all below modifications  +
• Photos for clarity  +
• Use D0015222 SY Grease Manifold as jig to … Use D0015222 SY Grease Manifold as jig to drill 2 off M5 tapped holes to secure Add M4 Tapped hole beside to fix a M4 cable tie base Assemble each SY grease manifold with 2 off M6 straight grease nipples and 2 off B0001061 Grease fitting M6 x 1 to 4mm as shown. Secure with M5 x 20 socket caps and A form washersith M5 x 20 socket caps and A form washers  +
• Use 1 meter straight edge to check alignme … Use 1 meter straight edge to check alignment of rollers Place straight edge against front face of rollers Use feeler gauges to check Mis alignment of rollers on the plain indicated Rotate rollers individually to check for eccentric rotation. Report any discrepancies above 0.002"/0.05mm to supervisorepancies above 0.002"/0.05mm to supervisor  +