Rechercher dans les propriétés de la page

Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.

Liste de résultats

• 1 Add m8 socket caps as shown to hold asse … 1 Add m8 socket caps as shown to hold assembly in vice 2 Use 2 off m8 long socket caps and Standard M8 nuts and lock onto drive coupling .
  
  ...Ensure end of socket cap doesn't touch inner part as rotation is required to tension
  Tension using long M8s as leverageas rotation is required to tension</div> </div> Tension using long M8s as leverage  +
• 1 Check bearing B0000086 Ball Bearing 15 D 32 D 9 Long + seals fit is acceptable on leadscrew H0007789 2 Adjust with emery tape if fit is tight  +
• 1 off 1 Remove 1 off Long M8 socket cap … 1 off 1 Remove 1 off Long M8 socket cap and tension an M8 x 12 kcp grubscrew into the hole (do not add adhesive ) 2 Remove second Long M8 socket cap and dimple inner shaft using 6.8mm drill Clean with compressed air and add M8x 8 kcp with adhesive and tension 3 Remove m8 x 12 kcp grub screw and repeat above step x 12 kcp grub screw and repeat above step  +
• 1 off Use the same steps above to assemble idler drive coupling as shown using D0008090 Retaining Collar x 1 <br/>  +
• 2 off Assemble P0000229 cylinder as shown  +
• 2 off 1 Check and adjust fit of B000013 … 2 off 1 Check and adjust fit of B0000139 Double Angular Bearing 20 D 47 D 20.6 Long + seals onto D0006501 Y Leadscrew Sleeve
  
  ...Only polish a small amount at a time , to ensure to correct amount is taken of the sleeve
  2 Fit should be a smooth press fit onto sleeve. Indicated face can be polished down with fine emery to obtain desired fitpress fit onto sleeve. Indicated face can be polished down with fine emery to obtain desired fit  +
• 2 off 1 Check fit of coupling to leadscrew H0007790 Leadscrew 2 Use reamer / Emery tape if fit is tight  +
• 4 off D0007629 . Clean M8 x 1.25 and M12 x 1.25 threads to remove debris  +
• <nowiki>2 off <br /><br /&g … 2 off
  
  
  1 Press B0000351 Bearing 40mm O/D 17mm I/D 17.5mm Wide into H0007715 Z Sprocket 33 Teeth 3/8'' pitch . Observe fit, if loose solvent to degrease and apply bearing fit. If tight inspect drawing and check bore size
  
  
  2 Press in D0007732 Sprocket Idler Shaft , again observing fit as above
  
  
  3 Fit 16mm external circlip
  
  
  4 Attach D0007733 Sprocket Mounting Block using M6 x 40 socket cap and heavy M6 washer (do not apply adhesive to this bolt )
  
  
  5 Add M6 x 30 grubscrew and M6 standard nut to indicated face (picture required)o this bolt )<br /><br /><br />5 Add M6 x 30 grubscrew and M6 standard nut to indicated face (picture required)</nowiki>  +
• Assemble a pair of cylinder assemblies as shown P0001038 Fitting: SMC 1/8" BSP to Ø6mm Elbow White x 4 P0001174 Fitting: Pilot Check Valve 1/4" (Flow & ZX) x 2 P0000140 Fitting: Quick Exhaust Valve 1/8" x 2 P0000200 Elbow Adaptor 6mm - M5 x 2  +
• Ensure D0001926 Servo Drive Coupling M20 (Ø14mm) Beckhoff x 1 fits onto C0001122K Servo Motor: Beckhoff AM8032-1E10 (Keyed) x 1 Fit should be a snug slide fit Part can be reamed with hand reamer if fit is tight  +
• Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised  +