Rechercher dans les propriétés de la page

Rechercher dans les propriétés de la page

Entrer soit une page et une propriété, ou seulement une propriété, pour récupérer toutes les valeurs affectées.

Affichage de 5 résultats à partir du n°1.

Voir (20 précédentes | 20 suivantes) (20 | 50 | 100 | 250 | 500).


    

Liste de résultats

  • # '[F4] Profiles' and press 'New Profile' # '[F4] Profiles' and press 'New Profile', type in the profile code and press ok # Scroll to the bottom to find your added profile # Enter the width of the profile, and the Z Support number from the Z axis tests (if required) If you want the profile to be "centralised" when clamping, add the name of the profile to a new line in the file names "Central.saw" a new line in the file names "Central.saw"   +
  • <div class="icon-instructions caution-i
    ...Do Not adjust a Zsupport position if it is already used for another profile!
    adjust the Z supports by winding the top bolt in/out on the Z turret. Once a Z turret position is determined, this profile is ready to be added to the machine.
    Once a Z turret position is determined, this profile is ready to be added to the machine.  +
  • Firstly, we need to make sure that the proFirstly, we need to make sure that the profile will physically go through the machine, open the top gaurd door. Ideally, you will have a 1 metre offcut of the profile - work out the best way for the profile to go through the machine. Push the profile through the machine by hand to ensure no catching areas etc.e by hand to ensure no catching areas etc.  +
  • If the profile did tip over: If tipped oveIf the profile did tip over: If tipped over it is most likely a 'Z' shaped profile - this means it will require an additional support, a small support block that comes out from the backfence to prevent the profile tipping. We have a turret system which allows up to 4 different rebate settings. Bring the Y40 Z turret to position number 1. This is done by turning the output (1) on (red) then off again (green) - this will move the Z turret system one position, use this table below to work out what position you are on:
    Position X34 Z Index A X36 Z Index B
    1 Off Off
    2 On Off
    3 Off On
    4 On On
    Use the Y30 Z support output (3) to fire the Z support blocks from the rear. Test your profile on each one in turn, find one that is suitable and note the support number (1-4). If none are suitable - you can adjust an unused one
    ...Do not try to turn the turret if the Z Support output is On

    . If none are suitable - you can adjust an unused one <div class="icon-instructions caution-icon"> <div class="icon-instructions-icon"><i class="fa fa-exclamation-triangle"></i></div> <div class="icon-instructions-text">...Do not try to turn the turret if the Z Support output is On</div> </div><br/>  +
  • Place the offcut in the machine, just undePlace the offcut in the machine, just under the saw top clamp. Now using the IO menu we are going to determine whether this profile wants to be cut normally or centralised and whether we require Z support blocks or not. Through the winSaw software press '[F6] Service' - we need to make sure we can clamp the profile with no issues. We will clamp the profile like we would when cutting normally. Press '[Y6] Side Clamp' and '[Y32] Saw Clamp'. If the profile clamps ok, goes through without catching anything and does not tip - this profile is ready to be added to the machine.
    ...If the profile catches the chip deflectors, It may be better located if the profile is "Centralised". Use the Y16 "Centralise" clamp instead of the Y6 "Side Clamp"
    ralised". Use the Y16 "Centralise" clamp instead of the Y6 "Side Clamp"</div> </div>  +