Rechercher dans les propriétés de la page

Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.

Liste de résultats

• 1 Assemble alignment disc to bearing outer . Hold in place with slightly tensioned M4 caps 2 Use an 8mm reamer to check holes will accept an 8mm dowel through both parts 3 Fit bearing outer cage onto alignment disc  +
• 1 Disconnect saw cut reed switches. Mark position of bracket before removal to aid re-assembly 2 Disconnect saw cut cylinder air pipes 3 Disconnect saw cut cylinder piston rod as shown  +
• 1 Disconnect the servo motor plug 2 Disconnect (if present) the m8 sensor plug 3 Remove m5 fixings around gearbox mounting flange to allow the gearbox and motor to be removed <br/>  +
• 1 Fit 2 off m6 shoulder bolts to opposing … 1 Fit 2 off m6 shoulder bolts to opposing m6 holes on gearbox mounting face and glue with loctite 270 permanent adhesive 2 Remove heads of shoulder bolts once tight 3 Deburr cut dowels 4 Test fit onto new d0004147E spigot shaft 5 Refit thrust bearing to main saw turntable housing and refit circlip
  ...Correct orientation of thrust bearing is paramount, Large inner face of bearing should face the gearbox side of the assembly
  6 Fit spigot shaft back into thrust bearing .
  ...If the fit is not resistive, use degreaser and bearing fit to the two mating faces to ensure correct operation of the bearing
  7 Refit hard stop to assemblynd bearing fit to the two mating faces to ensure correct operation of the bearing</div> </div> 7 Refit hard stop to assembly  +
• 1 Remove 6 of M8 caps heads from underneat … 1 Remove 6 of M8 caps heads from underneath main saw mount plate (3 per side ) 2 Remove 2 off m8 grubscrews locating saw cut shafts to turntable base
  
  Do not remove any other fixings on the saw head assembly when extracting. These 8 off fixings are all that are required to be removed, any additional fixings removed will compromise structure of assembly, and also mean that saw 90 degree vertical position will have to be manually reinstated once the upgrade has been completed
  3 The head assembly can then be removed by levering the base of the two saw cuts shafts , pushing them upwards to release the complete head assembly from the turntable basecuts shafts , pushing them upwards to release the complete head assembly from the turntable base  +
• 1 Remove hard stop, attached with 1 off m1 … 1 Remove hard stop, attached with 1 off m10 bolt and 2 off 5mm dowels 2 Remove internal circlip that captivates the centre thrust bearing 3 Remove bearing and spigot assembly as one from within the main bearing housing, and then remove bearing from the spigot shaft
  ove bearing from the spigot shaft <br/>  +
• 1 Remove saw blade 2 Remove saw cut dampe … 1 Remove saw blade 2 Remove saw cut damper buy removing 2 off m6 grubscrews and then retracting 2 off location pins 3 Remove top semi circular guard with slit strips attached, remove swarf chute and supporting T bracket 4 Remove top brace bar located on top of saw cut shafts as shown 5 Remove saw motor belts
  as shown 5 Remove saw motor belts <br/>  +
• 1 Remove stainless inspection cover 2 Remove 6 off m8 cap heads 3 Main turntable housing can now be removed, by lifting upwards through the main bottom plate  +
• 1 Remove the m8 caps from the top face off … 1 Remove the m8 caps from the top face off the turntable plate, along with the 4 off m4 caps. The remaining 8mm dowels visible cannot be extracted, but will be released once the turntable plate is removed. 2 To remove the plate , use leverage to force the plate up evenly, to expose the main bearing and alignment disc below 3 Now the top section of the main bearing and alignment disc can be lifted off, exposing the bores to access the gearbox fixings. 4 Remove the m6 cap head bolts as shown 4 Remove the m6 cap head bolts as shown  +
• Assemble alignment disc to bearing outer . Hold in place with slightly tensioned M4 caps Use an 8mm reamer to check holes will accept an 8mm dowel through both parts  +
• Connect the gear box , using the 2 dowels … Connect the gear box , using the 2 dowels on the gearbox as location, then using 4 off m6 x 20 blackadised unbrako bolts, loctite 243 and M0001176 4 off stainless lock washers to connect the parts together. Torque setting on 15nm should be used to set these m6 bolts Refit m5 Fixings to lower gearbox flange from underneath turntabler gearbox flange from underneath turntable  +
• Once the assembly is disconnected it can b … Once the assembly is disconnected it can be removed and allow access to the turntable base as shown
  
  ...This assembly will require a two person lift to remove from main saw area
  
  sembly will require a two person lift to remove from main saw area</div> </div><br/>  +
• Place turntable plate D4019E onto greased … Place turntable plate D4019E onto greased assembly , and fit 4 off 8mm dowels to fix all three new addition parts together. Then apply adhesive to m4 caps and tighten. Lastly fix with 4 off m14 bolts and a form washers to finalise turntable plate into position Check rotation is smooth by hand by turning the turntable plate and check the range of movement is correct
  k the range of movement is correct <br/>  +
• Refit bearing housing assembly to main plate  +
• Saw motor with mounting plate will now nee … Saw motor with mounting plate will now need removing from the saw head assembly 1 Disconnect saw anaconda as shown 2 Whilst supporting the saw motor, remove the 3 off m8 cap heads and swing the saw motor assembly and attach the frame , and secure for safe workingch the frame , and secure for safe working  +
• Thoroughly grease both bearings as this is a sealed for life unit. Liberal application of M0000494 grease is required  +
• Use steps 5-1 to complete the reassembly of the main components back onto the module  +