Rechercher dans les propriétés de la page

Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.

Liste de résultats

'''Updated photos for cylinder ai … '''Updated photos for cylinder air fitting required. Ports now face top!''' Finalise 32mm nut and 17mm nut on cylinders. Ensure both nuts are tightened when the cylinder is the closed position, to aid alignment To apply final tension to 32mm nut, it may be required to remove 1 off hardened shaft to allow correct access for tensioning nut Once all fixings are tensioned correctly, cylinder stroke travel should be smooth and consistent at all points of travel. No tight spots should be present at any area. travel. No tight spots should be present at any area. +
'''Updated photos for cylinder air fitting required. Ports now face top!''' Fit 4 off B0000236 90 Deg Grease Nipple M6 as indicated ( 2 per assembly) '''Use grease gun to apply grease to assemblies''' +
1 Fit 2 off P0000201 Flow Controller 6mm … 1 Fit 2 off P0000201 Flow Controller 6mm x M5 Elbow as shown 2 Remove fixing nut shown as not required 3 Fit 2 off P0000369 reed switch clamp as shown 4 Identify using markers 2 off P0000444 reed switches as X189 and X190 5 Fit P0000444 switches as shown . X190 goes to base, X189 goes to nose of cylinder. Use test box to accurately set and check function of reed switchesly set and check function of reed switches +
1 '''Updated photos for cylinder … 1 '''Updated photos for cylinder air fitting required. Ports now face top!'''

...White bearing seal must be removed from B0000034 bearings before fitting, this allows grease to enter bearings correctly when greased from greasing point

2 Fit B0000034 Linear Bearing 8 off into D0004591 Side Eject Housing. Ensure yellow seal of bearing faces outwards as shown 3 Attach 4 off P0001198 1/8 bsp 6mm speed controller to P0000035 Cylinder 25x160 2 off as shown 4 Fit assembled cylinder to bearing block orientated as indicated , and apply adhesive to large locking nut but do not tension 5 Fit D0004592 Eject Housing Plate and secure with M8 socket caps (size required) and Heavy M8 washers . Ensure these bolts are glued and tensioned correctly. 6 Insert 4 off H0004626 Shaft 16mm: 275 and fit 2 off D0004311 Side Eject Block orientated as shown. Wind in cylinder piston into eject block ,then Secure shafts by aligning dimples and securing with m8 x 12 kcp grubscrews
to eject block ,then Secure shafts by aligning dimples and securing with m8 x 12 kcp grubscrews +
1 Attach D0005202 Safety Dead stop Yoke to … 1 Attach D0005202 Safety Dead stop Yoke to D0005200 Safety Dead Stop Block as shown using M6 x 35 cap heads and A form washers 2 Attach dead stop block to D0005201 Safety Dead Stop Backer using D0005203 Safety Slider Cap 2 off. Fix as shown using M8 x 50 socket caps M8 penny washers and backed off with a M8 nyloc nut and M8 washer as shown3 3 Ensure part moves freely in the direction showne part moves freely in the direction shown +
<nowiki>Assemble valve bank orientat … Assemble valve bank orientated as shown

Use parts

P0001068 Valve Base: Type 41 2 Position Ø6 x 1

P0000174 Fitting: Plug 1/4'' BSP (Grubscrew Type x 2

P0001085 Fitting: SMC 1/4" to Ø8 Swivel Elbow x 1

P0001186 Valve/ 5/2 smc x 2

P0001163 1/4 bsp male silencer x 2lt;br /> P0001186 Valve/ 5/2 smc x 2 P0001163 1/4 bsp male silencer x 2</nowiki> +
Add identification markers to 2 off P0000- … Add identification markers to 2 off P0000-444 Reed switch pneumax Label as X134A and X135A Use P0000394 reed switch holder to secure to cylinder, orientate as shown Use test box to set switches in correct position Dokit link for upgrade [[Guide_to_Fitting_Eject_Push_Sensors_on_ZX_Machines]][[Guide_to_Fitting_Eject_Push_Sensors_on_ZX_Machines]] +
Air fitting position has been updated on the push eject assemblies Air fittings now face the top as shown +
All flow regulator fittings should be set to the following Adjust to the fully closed position (clockwise rotation) Adjust back 2.5 turns (anti clockwise) +
Attach pre assembled cylinder as shown Ensure indicated nut is glued and tight +
Please note that the area indicated on cylinders is not to be used to tension cylinders when fixing. If this area is used to add rotational force when fitting it will cause the cylinder to fail +
Use Loctite 243 on all fasteners Use Loctite 570 on all threaded pneumatic connections Pen mark all bolts when finalised +