Rechercher dans les propriétés de la page

Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.

Liste de résultats

• 1 Fit mounting bracket using 2 off M6 x 30 socket caps and heavy M6 washers 2 Attach interlock and guard panel using 4 off M5 x 60 socket caps, M5 penny washers and M5 Nyloc nuts  +
• 1 Adjust interlock switch assembly to alig … 1 Adjust interlock switch assembly to align exactly with fixed position of blade . Entry of blade into switch must be smooth and perfectly aligned 2 Mark position of second part of catch assembly with door closed , and drill 2 off M4 tapped holes into frame . Fix with 2 off M4 x 10 countersunk fasteners 3 Check closing and opening of door once all components are fitted in correct and well aligned . Not excessive force should be needed to overcome latch assemblyhould be needed to overcome latch assembly  +
• 3 Person lift Lift and position top hood onto frame Ensure cables feeding from saw top hood front corner are feed into area shown as the hood is fitted  +
• <div class="icon-instructions caution-i …
  ...ensure M6 hole 50mm from end of side rest is at the end shown
  Fit 3 off side rests as shown Use 6 off M6 x 10 socket caps and M6 penny washers 1 Set square to front tray 2 Ensure in fully forward position Set all 3 off to these settingsare to front tray 2 Ensure in fully forward position Set all 3 off to these settings  +
• All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added  +
• Check all fasteners are finalised. Inclusive of all upper and lower tray fasteners  +
• ECR Raised 13/12/23 Rework part to attached dimensions until ECR process issues amended part  +
• ECR raised 13/12/23 to amend and add holes Until processed rework at assembly to attached drawing  +
• ECR raised to amend door fixing block hole … ECR raised to amend door fixing block holes 1 Drill and tap indicated hole to M5
  ...Do not drill through !!!!
  2 Fit interlock blade using 1 off M5 x 20 socket cap and M5 A Forms washer , and align as shown 3 Mark position of second fixing hole and drill and tap to M5.
  ...Do not drill through!!!
  4 Finalise interlock with second M5 x 20 socket cap and A Form washer 5 Tap holes to remove debris and Fit 1st part of door catch using 2 off M4 x 10 countersunk bolts 6 Fit Second part of catch as shown 5 Tap holes to remove debris and Fit 1st part of door catch using 2 off M4 x 10 countersunk bolts 6 Fit Second part of catch as shown  +
• Fit 2 off chute inserts using 2 off M6 x 1 … Fit 2 off chute inserts using 2 off M6 x 12 socket caps and A Form washers
  
  ...Ensure electrical terminations behind these panels are complete before fitting guards
  
  erminations behind these panels are complete before fitting guards</div> </div><br/>  +
• Fit 4 off M6 x 60 socket caps with A form washers as shown Fit 3 off M6 x 12 socket caps and M6 A Form washers as shown Fit 2 off M5 x 12 socket caps and A form washers as shown  +
• Fit blade spanner to frame as shown Use 1 off M6 x 30 socket cap 1 off M6 penny washer 2 off M6 standard nut 1 off M6 A form washer  +
• Fit front compliance guard Position central on frame and 15mm up from lowest point of frame Drill and tap to suit M6 4 off Fix with 4 off M6 x 12 socket caps and M6 a Form washers  +
• Fit pre assembled front door to frame Use 6 off M4 x 12 button sockets only to fix hinges to frame. Ensure door sits square to frame  +
• Fit rear chute Use 4 off M6 x 10 button sockets to connect inserts to chute Use 6 off M6 x 12 socket caps with M6 A Form washers to connect chute to frame  +
• Fit rear door as shown using 4 off M6 x 12 socket caps Fit A Form M6 washers to lower 2 off socket caps only  +
• Insert cable through emergency stop from within machine  +
• Mark position for serial plate as shown … Mark position for serial plate as shown Mark and drill 1 hole only to 3.3mm Insert rivet into serial plate and drilled hole ( do not swell rivet) and mark remaining 3 holes Drill 3 off to 3.3mm Fix with 4 off rivets and finalise Fix with rivets rivets and finalise Fix with rivets  +
• Prepare frame for hood fitting Ensure cable indicated is as shown . Check frame bungs are fitted <br/>  +
• Remove lower fasteners from hinge panel and fit compliance guard in position  +