Rechercher dans les propriétés de la page

Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.

Liste de résultats

• 1 Position as shown smaller D0015357 S … 1 Position as shown smaller D0015357 Sensor Flapper Plate 2 Captivate with pivot block and dowel as shown, using same fixings as previous pivot block . Ensure dowel sits central in pivot block. 3 Ensure sensor plate is free to move in the direction shown when fitted. Sensor flapper should fall and return to its original position under its own weight. Leave as minimal gap as possible between pivot blocks and sensor plate Ensure sensor plate drops back under its own weight
  te drops back under its own weight <br/>  +
• 1 Assemble C0001018 EP2338-0001 EtherCAT … 1 Assemble C0001018 EP2338-0001 EtherCAT Box 8 Configurable IO onto D0010167 Ethercat Mount Plate x 1 as shown using M3 x 20 pan head fasteners 2 Fit to assembly Using 2 off M6 fat D nuts , M6 x 16 socket caps and A form washers at the position shown of 600mm from indicated face to edge of ethercat boxrom indicated face to edge of ethercat box  +
• Assemble frame as shown, using fittings supplied with D0015363 Maytec frame kit Set leg 1 to 405mm Set leg 2 to 305mm  +
• Check components Remove protective film … Check components Remove protective film from sensor flappers D0015355 Sensor Flapper Plate (312) x 6 D0015357 Sensor Flapper Plate (270) x 1 1 Ensure indicated have a radius on the indicated faces and are smooth and burr free 2 Ensure apex is flattened off, use linisher if required. This step is required to enable correction function of paddlesd to enable correction function of paddles  +
• Ensure all fasteners are double checked for correct tension, adhesive and identification to show finalised  +
• Ensure sensors are fitted to the correct s … Ensure sensors are fitted to the correct side of the sensor paddles. Sensors should be fitted to the radius side as shown 1 Fit 7 off M0001209 Bracket m8 proximity sensor bracket 90 deg. Position each bracket centrally beneath each sensor plate and orientate as shown Use M5 fat D nut, M5 x 10 socket cap and A form washer to secure 2 Fit 7 off E0000336L Sensor: M8; 4mm, PNP N/O, M8 conn as shown . 3 Set sensor gap to 5mm With the sensor plate fully depressed in the direction shown, set sensor so 5mm gap is present 4 Secure 2 off lock nuts on sensor. Caution do not over tension, as this can lead to damage to sensor !on, as this can lead to damage to sensor !  +
• Fit Cable tie bases using M5 x 10 button sockets an M5 fat D nuts at the positions shown (cables shown are fitted at a later stage)  +
• Fit 1st D0015353 Sensor Flapper Pivot as shown setting D nut flush with end of mounting bar. Fix with F0000299 m6 d nut and M6 x 20 socket cap  +
• Fit 2 off M0001016 Angle 74 x 38 as shown Fasten with M8 Fat D nut, M8 x 20 socket cap and Heavy M8 motor plate washers  +
• Fit D0015355 Sensor Flapper Plate (312) an … Fit D0015355 Sensor Flapper Plate (312) and fix with same method as previous steps
  
  ...Ensure mounting blocks are fitted square to enable correct operation of flapper plates
  
  are fitted square to enable correct operation of flapper plates</div> </div> <br/>  +
• Fit F0000537 dowel pin 10 x 40 as shown, leaving 5mm of protrusion Secure with M5 x 6 pointed grubscrew  +
• Fit remaining 5 plates in the same method as shown  +
• Use Loctite 243 on all fasteners Use Loctite 570 on all threaded pneumatic connections Pen mark all bolts when finalised  +
• Use vice to Fit B0001099 Bush flange 10 i/d 12 o/d x 14 into D0015355 Sensor Flapper Plate (312) x 6 and D0015357 Sensor Flapper Plate (270) x 1 as shown  +