Rechercher dans les propriétés de la page

Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.

Liste de résultats

• 1 6 off 2 7 off  +
• 1 Fit 8 off M0001006 Threaded insert M14 … 1 Fit 8 off M0001006 Threaded insert M14/M8 30 long to indicated points . Secure with Loctite 290 once fitted 2 Attach to D0015221 Outfeed Roller Bed Mounting Plate using M8 socket caps long enough to fix into m8 insert in the profile
  
  ...Tapped thread depth is not consistent on these parts so correct bolt length needs to be calculated each time
  3 Move piece indicated to top position and apply light pressure to integrated fixings 4 Attach D0015348 MC Outfeed Roller Mounting Plate again calculating correct M8 socket cap length . See picture for details of washers. Do not use adhesive on these bolts 5
  ...Note orientation of top plate in relation to bottom plate
  
  lt;/div> <div class="icon-instructions-text">...Note orientation of top plate in relation to bottom plate</div> </div><br/>  +
• 6 off Fit 2 off B0000415 bearing into D0010061 Datum Roller Ø40 x 20 '''''<u>Ensure bearings are pressed in far enough to be seated correctly on the shoulder below</u>'''''  +
• 7 off Fit 2 off B0000415 bearing into D0010396 Datum Roller Ø40 x 150mm Ensure bearings are pressed in far enough to be seated correctly on the shoulder below  +
• <div class="icon-instructions info-icon …
  ...only follow this step is bearing/shaft fit is loose
  Thoroughly degrease all parts with FE10 solvent 1 Fit 20mm external circlip to shaft 2 Fit roller to shaft 3 Add 3 drops of Loctite 641 bearing retainer to indicated area and smear around the shaft 4 Move shaft to shown position and add 3 more drops of bearing fit to indicated face and smear around 5 Position roller against circlip and remove any excess bearing fit with rag 6 Leave roller in a vertical position to allow bearing fit to cures bearing fit with rag 6 Leave roller in a vertical position to allow bearing fit to cure  +
• Check alignment of rollers as shown 1 … Check alignment of rollers as shown 1 Check with straight edge at both indicated points for roller alignment Report any gaps bigger than 0.002" 0.05mm 2 Check with straight edge at indicated point for roller alignment Report any gaps bigger than 0.002" 0.05mm
  any gaps bigger than 0.002" 0.05mm <br/>  +
• Check fit of following parts . Shafts sho … Check fit of following parts . Shafts should pass through bearings with only slight resistance . All inner bearing faces should have contact to shaft and rotate when the shaft is turned Proceed to step 8 if fit is correct If shafts are tight check drawing and inspect size of shaft . If shaft slides through easily, then follow step 7 check these parts D0010060 Roller Shaft Ø20 x 37.5 x 7 D0010061 Datum Roller Ø40 x 20 x 7 D0010396 Datum Roller Ø40 x 150mm x 7 D0010397 Shaft 20mm: 195mm Autoflow Roller x 70397 Shaft 20mm: 195mm Autoflow Roller x 7  +
• Ensure bearing fit is checked when assembl … Ensure bearing fit is checked when assembling parts . Minimal resistance should be required to fit these bearings into their respective rollers . Bearing should have enough contact on outer race that it will not rotate in the roller when turned If fit is to tight inspect roller bore size If fit is too loose, inspect to see within tolerance and if so , degrease and use bearing retaining compound
  and use bearing retaining compound <br/>  +
• It is vital that shaft dimples are correct … It is vital that shaft dimples are correctly aligned for Fixing grubscrews to locate properly To check correct alignment Insert shaft and visually align dimple through grub screw hole Insert grub screw and fasten Wind grub screw out 1/2 turn Shaft should be able to move slightly , but not be retracted from bore. This will confirm grubscrew and dimple are correctly alignedgrubscrew and dimple are correctly aligned  +
• Mount D0015217 Profile Support Pad x 2 as shown Use 4 off M10 x 25 socket caps to secure Use straight edge to set pads in line with rollers to 0.002" 0.05 mm or less . Report any discrepancies  +
• Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised  +
• excessive use of bearing fit can lead to bearing failure. Ensure only 2 matchhead size drops are used per bearing and smeared around shaft before fitting bearing  +
• mount rollers to bases as shown . Secur … mount rollers to bases as shown . Secure with M6 x 10 kcp grubscrews
  
  ...Ensure B0001176 washer : bearing shim is fitted between each roller as indicated
  
  6 washer : bearing shim is fitted between each roller as indicated</div> </div><br/>  +