Rechercher dans les propriétés de la page

Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.

Liste de résultats

• # Remove screw and band from P0001128 kit … # Remove screw and band from P0001128 kit # Bend ends of metal band to 90 degrees by hand ensuring thick metal plate is orientated as show # Fit screw through clearance hole and position reed switch assembly as shown # Attach to cylinder and fix in position with screw to cylinder and fix in position with screw   +
• 1 Fit bushes B0000437 x2 to body D001543 … 1 Fit bushes B0000437 x2 to body D0015431 2 Use 2 off 10mm x 40mm dowel. Ensure dowels fit correctly in nose D0015430. Check dowels have pushed all the way to the bottom of the bore . Secure with 2 off M4 x 4 grubscrew 3 Fit D0015090 Grip pin x 2 and secure with M5x 16 socket cap 4 Combine together and use m8 x 70 set bolt, a form washer and 2 x m8 half nuts to secure. Set gap to 13mm and lock all fasteners. Recheck measurement. Tolerance +-0.1mm
  ...Ensure loctite 243 and final tension is added to 2 off locking nuts indicated when setting grip nose gap
  
  2 off locking nuts indicated when setting grip nose gap</div> </div> <br/>  +
• 1 Fix as shown 2 off D0015100 brackets wi … 1 Fix as shown 2 off D0015100 brackets with 4 off M10 x 40 socket caps Do not apply adhesive or final tension to these fasteners 2 Mount Sensor bracket D0015292 with 2 off M5 x 30 socket caps, A form washers and M5 Nyloc nuts. Mount E0000336 as shown using both lock nuts and shake proof washers provided with sensord shake proof washers provided with sensor  +
• 1 Use M4 x 6 panhead to attach B0001181 rail to gripper base Fit M0001182 spring to main base 2 Use M5x 6 x 16 shoulder bolt and M4 x 6 pan heads to attach D0015756 lever to assembly Check gap indicated is 4mm  +
• 1 Add cable markers to E0001069 cable , Ma … 1 Add cable markers to E0001069 cable , Mark as X44 both ends 2 Attach above cable to E0000336L and fit as shown with 1 off supplied lock nut and shakeproof washer on the indicated face 3 Set Sensor position as follows Press lever fully in direction shown Adjust sensor to touch rear of profile present lever Adjust sensor back half a turn Lock of lock nut to hold position ( Do not over tension ) Check, when lever is pressed fully back, the sensor should be close to the profile present lever but not touchingthe profile present lever but not touching  +
• 1 Fit bushes B0001106 (20 off) to 8 off D0015095 link bars 2 off D0015096 link bars 2 Fit bearings B0000034 x 2 into D00015086 grip slide body. Use grease to lubricate bearing before assembly  +
• 1 Use 2 off D0015103 and 8mm external circ … 1 Use 2 off D0015103 and 8mm external circlips (B0000200) and assemble two off as shown 2 Use 2 off D0015102, 2 off D0015104 and assemble as shown with 8mm circlips 3 Use 2 off D0015170 gripper spacers and P0000049 spherical end and add as shown 4 Add remaining link shafts and circlips
  remaining link shafts and circlips <br/>  +
• Check shafts fit correctly into bores of D0015082 gripper bottom bar and D0015083 gripper upper bar  +
• Check that part D0015082 has been manufactured to the listed details highlighted in drawing attached to this step. If M4 and M5 holes are not present, rework and record time  +
• Combine parts 1 Use 2 off 6mm x 20mm dowels to align ( 1 top and 1 bottom) 2 M8 x 16 socket cap and A form washer 3 M8 x 20 countersink  +
• Due to many quality instances of incorrect … Due to many quality instances of incorrect fitting, please ensure the following steps are strictly adhered to 1 Remove grubscrew from P0001013 reed switch and dispose 2 Use metal retainer clip from P0001041 kit 3 Fit metal clip to reed switch as P0001013 reed switch as shown 4 Inset clipped reed switch into P0001041 bracket as shown, noting correct orientationacket as shown, noting correct orientation  +
• Ensure ecr change is present on D0015082 Indicated hole must be tapped tru as shown. If hole is not tapped thru, please rework by hand and record as rework  +
• Fit assembled cylinder unit to gripper fra … Fit assembled cylinder unit to gripper frame 1 Wind cylinder thread into spherical bearing lock cylinder nut off with 1 thread of cylinder piston exposed behind lock nut 2 Use M5 x 10 with a form washer to secure D0015097 2 off mounting plates 3 Use M8 x 30 with M8 nyloc nut to secure cylinder to brackets8 nyloc nut to secure cylinder to brackets  +
• It is vital the above fitted shoulder bolt is correct. Bottom of shoulder bolt should meet face of gripper base as shown No thread should be visible when fitted correctly  +
• Please ensure when assembling components t … Please ensure when assembling components that attention is paid to mating faces and the correct alignment These rebates are to aid assembly and ensure squareness when built Faces must be butted to each other to be assembled correctly Please see picture for an example of incorrectly assembled mating faces and also correctly assembled mating faces and also correctly assembled  +
• Several instances of the following step have been encountered. Please ensure all fixings are sufficiently tight and adequate Loctite 243 is used on ALL fasteners  +
• The load switch must be assembled that enables free running and not tight spots to be encountered when operated. Please ensure assembly guidance is followed and adhered to. If any issues arise please advise supervisor for correct action  +
• Use 2 off D0015085 1 Assemble as shown using 8 off M8 x 20 socket caps and 4 off M6 x 12 socket caps 2 Check top and bottom bars are parallel 3 Check grip slide moves freely up and down  +
• Use 4 off A0001044 p clips 4 off M4 x 12 socket caps and captivate X44 cable at points shown  +
• Use Loctite 243 on all fasteners Pen mark all bolts,nuts and fasteners once finalised  +