Rechercher dans les propriétés de la page

Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.

Liste de résultats

• '''<u>Please capture pictures for th … '''Please capture pictures for these steps''' 1 Fit pulley as shown to D0004734 Belt Adjusting Bar using M8 x 50 set bolt, M8 Penny washer and backed off with M8 standard nut. 2 Fit assembly to D0004078 Motor Plate as shown using M8 x 25 socket cap and Heavy duty M8 washerhown using M8 x 25 socket cap and Heavy duty M8 washer  +
• 1 Add M6 x 6 grubscrew to indicated hole … 1 Add M6 x 6 grubscrew to indicated hole and secure with Loctite 572 2 Fit 2 off B0001061 Grease fitting to indicated points 3 Assemble D0010780 Grease Manifold as shown using 1 off B0001061 grease fitting and 3 off B0000234 grease nipples (consumable stock) Use loctite 572 on threads 4 Fit to bearing block using 2 off M4 x 16 socket caps 5 Fit 1 off B0000234 grease nipple to indicated point
  grease nipple to indicated point <br/>  +
• 1 Mount cylinder bearing block and 2 off … 1 Mount cylinder bearing block and 2 off bearing block as indicated to D0004021 Upstroke Plate. Lightly secure with M6 x 25 socket caps and A form washers . Do not apply adhesive 2 Mount remaining bearing block as shown, incorporating D0004343 Lower Damper Bracket as shown . Use M6 x 25 socket caps, again do not apply adhesive or apply final tension not apply adhesive or apply final tension  +
• 1 Add 3 off m4 tie base and secure with M4 x 6 button screws as shown 2 Cut and fit 1 off yellow grease pipe to follow route indicated  +
• 1 Add two 28mm internal circlips to D00047 … 1 Add two 28mm internal circlips to D0004733 Belt Adjuster Pulley 2 Fit 2 off B0000002 Bearing to pulley as indicated. Be observant of bearing fit, if bearing fit is loose use Degreaser and apply Loctite 641 If fit is tight ,check components to drawings 3 Fit D0004735 Belt Adjuster Pin as shown, observing above regarding correct fitment. Check smooth operation of bearings once fittedk smooth operation of bearings once fitted  +
• 1 Assemble D0004445 Semi circular slit str … 1 Assemble D0004445 Semi circular slit strip onto D0004634 Chute Sawblade Strip as shown using 2 of M6 x 30 socket caps. Ensure all edges of parts are aligned flush when assembled 2 Fit H0004444 Semi-circular Guard as shown using 4 off M5 x 10 countersunk bolts. Ensure countersunk bolts sit flush when fitted. Adjust with countersink tool if sitting proud when fitted
  
  ...Countersunk bolts must sit flush on guard panel. Use countersink tool to deepen if they sit proud
  
  h on guard panel. Use countersink tool to deepen if they sit proud</div> </div><br/>  +
• 1 Attach 2 off P0000009 Fitting as shown 2 Attach D0004256 Cylinder rod bar as shown, and finalise lock nut 3 Attach P0000308 Flow Controller In Line 6mm to indicated fitting and connect with a 50mm long piece of 6mm black air pipe labelled as 2079  +
• 1 Degrease D0004099 Cylinder Bearing Block and fit 1 off B0000032 Linear Bearing. Ensure yellow seal of bearing is on indicated face 2 Fit B0000032 Linear Bearing with yellow seal to indicated face of Degreased D0004001 Head Bearing Block  +
• 1 Fit 3 off m4 tie bases and secure with M4 x 6 button heads at indicated points 2 fit and secure 2 lengths of 4mm yellow grease line and secure as shown  +
• <div class="icon-instructions caution-i …
  ...When fitting blanking grubscrew, only fit to a flush position. Further depth will impede bearing operation
  1 Fit B0001061 grease fitting to indicated face using Loctite 572 on threads 2 Fit M6 x 6 blanking grubscrew to indicated face using Loctite 572 Assemble 3 off in total as aboveblanking grubscrew to indicated face using Loctite 572 Assemble 3 off in total as above  +
• All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added  +
• Check upstroke plate has helicoils fitted in indicated holes. M8 thread will be present if they have, thread will be larger than M8 if they havent Use workshop helicoil kit and add M8 x 1.5 od helicoils if not present  +
• ECR has been raised to amend part D0004734 … ECR has been raised to amend part D0004734 02/04/24 Amended to length has been requested. Part now needs to be 120mm long instead of 139.7mm If supplied part has not been produced to shorted length, please rework part to new length of 120mm long ensuring a good quality of finish is achieved when cuttingquality of finish is achieved when cutting  +