Rechercher dans les propriétés de la page

Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.

Liste de résultats

• 1 Fit Circlip 20mm and D0015801 Feather … 1 Fit Circlip 20mm and D0015801 Feather Key 8mm x 8mm x 22mm as shown 2 Fit D0008585B Rotary Ring Drive Pulley as shown . Only press down until circlip groove is present 3 Fit 20mm external circlip 4 Tighten Grubscrew with pulley pulled against circlipubscrew with pulley pulled against circlip  +
• 1 Attach tensioning jig as shown 2 Apply tension to belt , spreading tension over two bolts indicated . Maintain parallel on these faces as adjusting Set belt tension to 5mm deflection (Drum Tight )  +
• 1 Fit D0007849 Servo gearbox cap as shown. No adhesive on the 4 off M8 x 35 socket caps Orientate as shown 2 Fit D0000268 pulley  +
• 1 Fit B0000095 bearing to D0006058 plate a … 1 Fit B0000095 bearing to D0006058 plate as shown . Note circlip on bearing to be on indicated face 2 Attach B0000092 Belt: Toothed 640-8MGT 20 as shown 3 Press pinion assembly onto gearbox plate
  
  ...Do not force past contact point indicated. This can cause distortion on pinion assembly
  4 Secure lightly with 4 off M6 x 35 socket caps 5 Add 2 off 8mm x 50mm dowels into indicated holes . Ream if holes are tight 6 Finalise 4 off M6 socket caps 50mm dowels into indicated holes . Ream if holes are tight 6 Finalise 4 off M6 socket caps  +
• 1 Press B0000095 Bearing into D0006060 Spi … 1 Press B0000095 Bearing into D0006060 Spigot Cap so snap ring sits flush 2 Fit D0001286B-2MOD Welded Ring Pinion Gear 2MOD as shown Use jig to ensure bearing is not moved from location. Push through until circlip groove is in correct place Check to ensure drive pinion does not contact bearing face as shownion does not contact bearing face as shown  +
• <div class="icon-instructions caution-i …
  ...Ensure plastic bung issued with gearbox remains with gearbox at all times for later fitting
  with gearbox remains with gearbox at all times for later fitting</div> </div>  +
• Adjust pulley 1 up or down to match pulley 2 as shown  +
• Check D0000268 Rotary Drive Tooth Pulley … Check D0000268 Rotary Drive Tooth Pulley fits onto C0001211 Gearbox If pulley fits move to step 6, if it does not fit follow these steps 1 Remove key from gearbox shaft
  ...Take care not to damage shaft or keyway . Try clamping keyway in a vice to remove from shaft
  2 Test pulley again for fitment. * If the pulley still does not fit, polish inner face of pulley until fitment is achieved * if the pulley does fit when the key is removed , move to next step 3 Refit key 4 Test pulley , if the pulley still doesn't fit correctly dress keyway slot gently until fit is achieved, if the pulley still doesn't fit correctly dress keyway slot gently until fit is achieved  +
• Insert part1 through part 2 Hook over belt (3) insert 4 off m8 x 50 with a form washers a pull to face lightly  +
• Quality check required on belt tension  +
• Reverse steps to remove assembly 1 Remo … Reverse steps to remove assembly 1 Remove part 2
  
  ...Ensure pulley retains its position through these steps
  Tighten grubscrew to leave witness mark , Remove pulley and drill 5mm dimple at indicated point Use M6 x 10 kcp grubscrew to lock pulley in final position Rebuild parts to get to 3
  Use M6 x 10 kcp grubscrew to lock pulley in final position Rebuild parts to get to 3 <br/>  +
• Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised  +
• finalise 4 off m8 socket caps to hold tension Remove setting jig plates  +