Rechercher dans les propriétés de la page

Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.

Liste de résultats

• 1 Fit D0004393 Lever Joint x 2 using Loc … 1 Fit D0004393 Lever Joint x 2 using Loctite 270 onto D0004541 Cylinder Swivel End x 2 2 Hold as shown in vice and tighten 3 Remove any burrs from tightening 4 Check fitment of D0004393 Lever Joint x 2 onto assembled components. Lever joint should fit easily onto assembly and turn freely. Polishing with emery may be required if fit is tight 5 Clean and add copper slip as shown to pin , and fit into lever joints 6 Add M6 x 10 pointed grubscrew with Loctite 270 and wind in until the V on the pin has been touched with the grubscrew. adjust grubscrew so rotation is possible but no end float is presenton is possible but no end float is present  +
• 1 Modify M6x 35 socket cap and reduce len … 1 Modify M6x 35 socket cap and reduce length by 10mm and use to attach damper to rod end block Assemble P0000029 Non Adjustable Damper 100mm with D0004669 Damper Rod End Block '''Ensure rod end block is orientated as shown''' Use m6 x 10 kcp grubscrew to secure bolt in rod end block Rod end block should be able to swivel once assembled and fasteners are tightvel once assembled and fasteners are tight  +
• 1 Position D0004406 Retainer Plate as sho … 1 Position D0004406 Retainer Plate as shown 2 Fit D0004403 Pivot Pin Nut as shown 3 Tension nut until centre spacer can just be moved in the indicated direction ('''please take photo of how this is done with flat head''') 4 Add locking bolt M5 x 16 to pivot nut and tighten. Recheck movement indicated, and if this has changed, slacken locking bolt, adjust pivot nut and tension locking bolt again bolt, adjust pivot nut and tension locking bolt again  +
• 1 Attach B0000065 Bearing Rod End to D0004 … 1 Attach B0000065 Bearing Rod End to D0004370 Middle Link Stud Bolt as shown using Loctite 270 2 Fit to D0004363 Middle Link Rod using Loctite 270 and tighten fully 3 Assemble B0000065 Bearing Rod End onto D0004369 Top Link Stud Bolt using loctite 243, then add 2 off M10 standard nuts as shown. Add Loctite 243 onto exposed thread and wind into D0004363 Middle Link Rod 4 Use pitching jig to correctly set pitch of tie bar assembly. Slightly tension assembly on jig, then remove and add final tension to all M10 nutsmove and add final tension to all M10 nuts  +
• 1 Degrease bore of D0004365 Pivot Clamp 2 Add a smear of loctite 641 to bore and fit bearing assembly 3 Use 2 off M6 x 16 socket caps with A form washers to finalise  +
• 1 Fit B0000005 Angular Contact Bearing to … 1 Fit B0000005 Angular Contact Bearing to D0004401 Pivot Pin as shown. Ensure bearing is orientated the correct way. Larger inner face should be as shown . Ensure correct bearing fitment is present . If bearing is a loose fit, loctite 641 should be used . If fitment is to tight, inspect parts to drawing for discrepancies Lubricate bearing with grease 2 Fit D0004407 Pivot Bearing Spacer and second B0000005 Angular Contact Bearing, again observing orientation ( second bearing is fitted opposite to first) Apply grease to second bearing to first) Apply grease to second bearing  +
• Assemble 2 off P0000031 Pneumax Microcylinder 25 x 100 Magnetic as show. Fit 2 off P0000295 Elbow Adaptor 6mm - 1/8 BSPT (Metal type) and 2 off P0001198 fitting speed controller 1/8 x 6mm tube  +
• Attach 2 off P0000049 Cylinder Spherical Bearing M10 x 1.25 as shown . Tighten and finalise  +
• Check fitment of D0004401 Pivot Pin and D0004403 Pivot Pin Nut Nut should spin down shaft thread with little resistance Report any anomaly to supervisor  +
• Connect H0004367 Centering lever to pivot assembly using D0004766 Pivot Pin Bolt as shown . Finalise with M10 standard nut and A form washer Once assembled, rotation of pivot assembly should be smooth and consistant when turned  +
• Mount assemblies together as shown ..Ensure air fittings are angled in the same direction as shown. Finalise locking nuts  +
• Tie rod should be reduced in length by 1.5mm (1 full turn of rod end) This should be done after initial setting on set up jig  +
• Use M8 x 25 socket caps and A form washers to mount assemblies to centre levering bar as shown  +
• Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised  +