Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.
Liste de résultats
- 1 Fit 2 off 5mm x 28mm dowels to D0010778 Turntable Stop Arm Use Loctite 270 to secure 2 Cut down dowels to 6mm protrusion 3 Fit to flat on turntable pin and secure with 4 off M10 x 50 socket caps +
- 1 Fit 4 off B0000032 Linear Bearing: Ø30 x … 1 Fit 4 off B0000032 Linear Bearing: Ø30 x 50 Compact bearings to D0004516 Front Bearing Block (5294) x 2 as shown , ensure bearings are greased after fitting 2 Attach D0004514E Turntable Base Mk5 as shown . Use M6 x 25 and M8 x 25socket caps to fix . Ensure all external faces are flush with bearing blocks 3 Clean 2 off H0004631 Shaft 30mm, Fit 4 off M8 x 40 socket caps and A form washers to indicated holes . Insert through bearing blocks . Ensure dimple in shaft is at the indicated end 4 Fit D0004336 Stay Bar x 2 as shown. Use M8 x 12 kcp grubscrews to locate onto shaft dimple. End of shaft with no dimple, set staybar flush with shaft and tighten grubscrew onto shaft If the stay bars are a tight fit, these will require polishing with emery tape to remove debris from coating process . Ensure gradually polishing of bores to ensure bores are taken oversize 5 Check and finalised all fixingsversize 5 Check and finalised all fixings +
- 1 Fit bearing cage from B0000028 Thrust Be … 1 Fit bearing cage from B0000028 Thrust Bearing 140 I/D 180 O/D 31 Long (FAG), Apply more grease then position assembly shown on top and visually align 8mm reamed holes 2 Position D0004019E Turntable Mk5 as shown. Ensure hard stop is in centre position All 8mm reamed holes should align through the 3 parts. Turntable shaft, alignment disc and turntable 3 Add 2 off m4 x 20 socket caps and tension lightly to indicated holes to fix together 4 Insert 4 off 8mm x 50mm hardened dowels to fix all three parts in correct alignment 5 Remove 2 off previously fitted M4 socket caps, apply adhesive and apply final tension 6 Add 4 off m14 x 60 socket caps and A form washers to finalise fixing of turntable plate Check rotation once assembled . Movement should be smooooooth and consistentvement should be smooooooth and consistent +
- 1 Mount Built base as shown, using clamps … 1 Mount Built base as shown, using clamps and spacer blocks. This is a two person lift . Ensure clamps are fitted as shown to allow fitment of brackets later on
2 Insert built turntable, orientated as shown.
3 Fit D0010796 Turntable Housing Cover using m4 x 6 button sockets 6. Housing can be rotated for easier access when fitting cover
4 Fix with 5off M8 x 35 socket caps and A form washers and 1 off M8 x 25 socket cap with no washer
M8 x 25 socket cap with no washer <br/> + - 1 Remove key and Degrease thoroughly spind … 1 Remove key and Degrease thoroughly spindle on C0001122K Servo Motor: Beckhoff AM8032-1E10 (Keyed)
2 Insert motor into gearbox and orientated servo plug as indicated
Affix motor to gearbox using M5 socket caps (size required)
3 Tension friction coupling to 9.5nm using torque wrench , then insert gearbox bung . Write torque setting on indicated face
te torque setting on indicated face <br/> + - 1 Use 8mm hand reamer to clean holes indicated in D0004033E Alignment Disc Mk5 2 Attach smaller bearing outer cage to disc using press 3 Use 8mm hand reamer to clean indicated holes on D0004019E Turntable Mk5 (5334E) +
- All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added +
- Fit D0015663 SR Axis Motor Guard as shown . Use M5 x 16 socket caps and a form washers to fix . Note correct orientation of offset of part +
- Fit 4 off mounting brackets for later installation to main saw frame Details of fasteners required please +
Français
English
Deutsch
Español
Italiano
Português