Rechercher dans les propriétés de la page

Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.

Liste de résultats

• 1 Fit 1 off B0000380 bearing to D0007797 as shown. Ensure correct bearing fit is observed 2 Fit to D0007750 backplate and secure with 4 off M6 x 16 socket countersunk 3 Fit D0007730 spindle 4 Fit D0007729 spacer 5 Fit 2nd B0000380 bearing  +
• 1 Check fit of Motor drive gear D0007873 … 1 Check fit of Motor drive gear D0007873 onto B0000335 motor. Ensure fit is smooth and pinion can be fitted by hand. 2 If gear does not fit onto spindle by hand, remove key from motor shaft and * Check motor gear fits on shaft with no key present. If not rework bore of motor gear to ensure correct fitment * Check key passes through motor gear keyway . If not rework keyway until key passes through by hand * Re fit key and check motor gear now fits by hand onto motor shaft 3 Set motor pinion flush to top of shaft and secure with 2 off M6 x 10 KCP grubscrews and Loctite 243. Ensure these are fully tightenedtite 243. Ensure these are fully tightened  +
• 1 Degrease mounting faces indicated with FE10 solvent 2 Apply bead of Hylomar as shown to drive pinion housing 3 Fit housing to motor, paying attention to orientation and fix with 4 off M6 x 50 socket caps  +
• Always use Loctite 243 on all fasteners fitted unless stated different All bearings should be an acceptable fit, with Loctite 641 and FE10 solvent used if required All fasteners should be marked once finalised  +
• Apply Hylomar as shown Apply Loctite 64 … Apply Hylomar as shown Apply Loctite 641 to bearing Fit assembly to main housing
  ...Hole fixing PCD must be observed to allow correct alignment . If not aligned correctly, all 3 fixing M6 holes will not align. Check orientation before fitting assembly
  
  es will not align. Check orientation before fitting assembly</div> </div><br/>  +
• Combine 2 assemblies as shown. Use location dowels to position Fix with 3 off M8 70 socket caps and Loctite 243 Smooth excess Hylomar with clean rag once fasteners have been finalised  +
• Degrease indicated faces with FE10 solvent  +
• Degrease indicated faces with FE10 solvent Apply 1/3 of tube of M0000603 grease as indicated Apply Hylomar to face as indicated  +
• Ensure bevel gears are identified correctly D0007868 has an additional raised face on the rear of the gear  +
• Fit 2 off B0000043 bearings to housing D0007870 Ensure correct bearing fitment is achieved. Use loctite 641 and thoroughly degrease with FE10 is bearing are loose in bore  +
• Fit B0000105 bearing to shaft D0007875 , ensuring correct orientation Use loctite 641 and FE10 if bearing fit is loose  +
• Fit B0000382 key to shaft Fit D0007874 gear to shaft  +
• Fit Key B0000383 to Shaft , and fit bevel gear D0007868 , ensuring correctly orientated  +
• Fit assembled shaft to bearing housing as shown Again, observe fit of bearings and if required, use Loctite 641 bearing fit and FE10 solvent to correct if bearings are loose  +
• R0000728 and R0000729 are mirror images to each other Please inspect pictures to clarify and confirm correct hand to be built (Supplied unit to be refurbished will always be rebuilt as the same hand )  +
• Use M6 x 20 socket countersunk with D00078 … Use M6 x 20 socket countersunk with D0007876 washer Use M6 x 20 button head with M6x 20 penny washer Use Loctite 243 and ensure all threads and tapped holes are thoroughly degreased with FE10 solvent Fit fasteners as shown and tighten both fasteners at the same time, using opposing threads to enable sufficient tensioningng threads to enable sufficient tensioning  +