Rechercher dans les propriétés de la page

Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.

Liste de résultats

• # Create THREE manual input pieces 5m [] … # Create THREE manual input pieces 5m [] and add the "Calibration Notch" at 250mm intervals from 250mm to 4750mm # Run all 3 bars
  
  ...It is important to use the CAL notch rather than the old standard datum test because it is much easier to measure and is produced much more quickly
  
  ause it is much easier to measure and is produced much more quickly</div> </div><br/>   +
• #Cut a long bar length - as long as you c … #Cut a long bar length - as long as you can given the standard length and capacity of the machine. In our test we used 5m bar lengths cut from 5.3m standard lengths #Measure bar length to your chosen tape rule. #Adjust the scaling of the machine to ensure the cut bar is 5m long +/-0.5mm
  sure the cut bar is 5m long +/-0.5mm <br/>   +
• <div class="icon-instructions info-icon …
  ...When the software searches for a rackoffset value in the file, it looks for the x axis position in the files NEAREST to the intended position
  the x axis position in the files NEAREST to the intended position</div> </div>  +
• Add the positions from the step above alon … Add the positions from the step above along with the offsets Press Save
  
  ...The rackOffsets.mul file stores these values if you need to edit them manually or add more than listed
  
  e values if you need to edit them manually or add more than listed</div> </div><br/>  +
• Compare the position of the slots on each … Compare the position of the slots on each of the 3 bars with respect to each other. by lining the up together (regrettably photo does not show this) '''If the 3 bars are not identical, the root cause is not linearity.''' Do not proceed with this process, the root cause will be mechanical play in *Clamping *Gripping *Alignment *Loose Components Or possibly drive tuningLoose Components Or possibly drive tuning  +
• In the Service Form->Bar Data you can find the operation positions in the bar tree You only need the CALNOTCH positions, not the saw cuts  +
• It is vital that you use a measuring tape … It is vital that you use a measuring tape that is linear in scale, and reasonably accurate. It is even more important that you use one (AND ONLY ONE) measuring tape throughout this test. It is not critical that the tape is 100% accurate - that is impossible - but what is important is that you consistently use the same tape.
  ...Always choose one tape measure to run these tests. No two tape measures are the same. Choose one and stick with it
  The linearity of the tape can be checked using a simple process # Using the distance between 100mm and 1100mm, make out a "Standard" metre on a flat, solid, consistent surface (use 100mm and 1100mm to ensure there is no error at the zero point # Check the zero point is consistent - discard the tape measure if it isn't, it will be a pain otherwise # Check the areas 1000-2000mm, 2000-3000mm, etc against the "standard" metre It could be the case that your "standard" metre is not really a metre exactly, but that does not matter. What is important is that a metre means the same thing all the way along the tape. '''That is linearity'''t is that a metre means the same thing all the way along the tape. '''That is linearity'''  +
• Maintaining a constant bar temperature is … Maintaining a constant bar temperature is incredibly important during these tests. Profile grows 0.07mm per metre per degree of temperature rise, so if you source a test bar from outside at 0 degrees, then the machine is near a heater at 20 degrees, a 6m bar will have grown by 8.4mm as it heats up! given that we will be measuring increments of 0.25mm, '''this is serious...''' The simple solution is to ensure the bars are at room temperature before you start. Keep the doors closed during the tests. Keep an eye on the overall length of the bar by using the same measuring tapef the bar by using the same measuring tape  +
• Run the linearity test from above again. Success will be all the notches in the place they should be with no discernable offset  +
• Write the error +\- next to each notch, me … Write the error +\- next to each notch, measuring from machining centre end (photo shown is RtoL feed machine). Repeat for each notch on each of the 3 bars Again, check for consistency. If there is any doubt that the results have not repeated consistently 3 times, then do not proceed consistently 3 times, then do not proceed  +