Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.
Liste de résultats
- <div class="icon-instructions idea-icon …
With the old 400mm blade fitted operate the saw to widen the gap in the slit strip. WD40 can be applied to the blade as a lubricant which will also help minimise the noise that will be made.
After first cut the saw out sensor will need to be adjusted to allow for the extra stroke length.
'''IMPORTANT'''
'''Before carrying out the next step it is vital to check that the new blade will not cut into the interlock on saw top door.'''
Remove the 400mm blade and replace it with the new 500mm blade. Apply WD40 to blade and operate the saw blade to fully cut the slit strip.
blade. Apply WD40 to blade and operate the saw blade to fully cut the slit strip. <br/> + - <div class="icon-instructions idea-icon … Remove rear saw door/cover and remove half moon plate. An extra 50-60mm needs to be removed using a jigsaw to allow clearance for the new blade. An extra 50-60mm needs to be removed using a jigsaw to allow clearance for the new blade. +
- <div class="icon-instructions info-icon … Adjust flow regs for 45/90/135 degrees and also saw out stroke to minimise blade wobble. Check operation of saw blade at all three angles.aw out stroke to minimise blade wobble. Check operation of saw blade at all three angles. +
- Fit the new pulleys and belts, no need for … Fit the new pulleys and belts, no need for Loctite on the grub screws Check alignment of belts and tension. Fit old blade. The old blade can be used to cut a little clearance in the new slit strip before the 500mm blade is fitted. If this is not done then the motor overload may trip as the 500mm blade can be stalled by the tight gap in the slit strip.talled by the tight gap in the slit strip. +
- On later machines, the top door guard swit … On later machines, the top door guard switch is bigger, and therefore will get cut by the 500mm saw blade at the absolute top of its travel See this [https://stuga.dokit.app/wiki/TB0338_Saw_500mm_Blade_Upgrade_Switch_Block_Relocation Technical Bulletin] for detailsRelocation Technical Bulletin] for details +
- Remove clamp pads and pull out old shafts. … Remove clamp pads and pull out old shafts. Remove old cylinders and replace with long reach ones. Lubricate bearings before fitting the nit new shafts and chip deflectors. Spacers may need to be put behind side clamp cylinders as well as cutting 5mm from end of the shafts. The lock nut may also have to be moved to the other side of the bracket. This is only required if the cylinder rod end fouls on the top clamp cyclinder. Check and adjust stroke of side clamp cylinders when they are in the extended position used when the saw is centralised.position used when the saw is centralised. +
- Remove the four countersunk and four dome head allen screws holding the slit strip. These can quite often be siezed and/or be rounded and my need to be drilled out. Fit new slit strip. +
- Remove the two grub screws from the taper … Remove the two grub screws from the taper lock pulleys and insert one into the hole that was initially empty. Screw in tight to break seal of taperlock and split the two parts. If siezed the outer part can be tapped back with a hammer. These parts are usually very brittle and can shatter with a heavy hammer blow. It can also be useful to have the belts on at this point to stop the pulley from turning.his point to stop the pulley from turning. +
- Using the old slit strip you can wedge up the assembly to give easier access. Once wedged up place something underneath the assembly to stop it falling on your hands if the slit strip slides off. Remove the old bracket and replace with the new one. +
Français
English
Deutsch
Español
Italiano
Português