Voir la source de Commissioning - Off-Cut Laser Sensor

{{Tuto Details
|Main_Picture=Commissioning_-_Off-Cut_Laser_Sensor_laser1.PNG
|Main_Picture_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":14,"top":-43,"width":474,"height":490,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1.11,"scaleY":1.11,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/2/2c/Commissioning_-_Off-Cut_Laser_Sensor_laser1.PNG","filters":[]}],"height":450,"width":600}
|Description=<translate>Setting up the laser sensors on the infeed of a Flowline, ZX4 and ZX5.</translate>
|Categories=Maintenance
|Difficulty=Easy
|Duration=10
|Duration-type=minute(s)
|Tags=Laser Sensor, ZX4, ZX5, Flowline, Commissioning
}}
{{Introduction
|Introduction=<translate>Infeed Off-Cut Laser sensors are used to check the length of profile with the proposed length from the software. This is to avoid incorrect lengths and profiles being cut. The sensors will be put at specific lengths along the infeed which will be input in the software files. When profile hits the back fence all covered sensors will trigger, hence, the profile must be larger that the final triggered sensor.</translate>
}}
{{TutoVideo
|VideoType=Vimeo
|VideoURLVimeo=https://vimeo.com/294109652
}}
{{Materials}}
{{EPI}}
{{Tuto Step
|Step_Title=<translate>Adjust the "Light Dark"</translate>
|Step_Content=<translate>Adjust the "'''Light Dark'''" balance on the sensor. To do this, using a small flat head screwdriver, turn the light dark dial '''clockwise''' until the orange light goes off. Then slowly turn '''anti-clockwise''' until the orange light turns on again, when this happens re-turn a '''little clockwise''' to turn off the orange light.</translate>
|Step_Picture_00=Commissioning_-_Off-Cut_Laser_Sensor_laser1.PNG
}}
{{Tuto Step
|Step_Title=<translate>Adjust Sensitivity</translate>
|Step_Content=<translate>Now adjust the sensitivity. Place an object '''80mm''' away from the sensor. Now adjust the sensitivity until the orange light turns on.</translate>
|Step_Picture_00=Commissioning_-_Off-Cut_Laser_Sensor_laser2.PNG
}}
{{Tuto Step
|Step_Title=<translate>Sensor Height Warning</translate>
|Step_Content=<translate>Make sure the height of the sensor is '''ABOVE''' the gaskets on profile.</translate>
|Step_Picture_00=Commissioning_-_Off-Cut_Laser_Sensor_Laser4.PNG
}}
{{Tuto Step
|Step_Title=<translate></translate>
|Step_Content=<translate>From the 0 Position measure the distance of each sensor. These should be written down on the sensors. In the measurements settings ([https://elearning.stuga.co.uk/mod/page/view.php?id=67 winMulti] > Settings > measurements) update each “offcutSensorX” parameter with the exact measurements recorded.</translate>
}}
{{Notes}}
{{PageLang
|Language=en
|SourceLanguage=none
|IsTranslation=0
}}
{{Tuto Status
|Complete=Draft
}}