]> 2026-04-27T22:58:07+02:00 ZX5 Transfer Table Setup 0 en Published How to correctly set mesh between racks/pinions, V rail and delrin rollers Easy 20 minute(s) Sometimes the mesh between all the parts is too tight and left with no adjustment. This causes too much pressure on the moving parts, especially the delrin rollers which are not designed to take heavy loads. Any excess force on them leads to excessive wear and premature failure. false en ZX5_Transfer_Table_Setup_Correct_Pinion_Adjustment.jpg none The rollers on top are mounted on eccentric bushes. We only need these just tight enough to not allow any slop or vertical play. Slacken the cams off completelely, you will need an 8mm spanner with the faces ground down to fit in the space. Slide the plate onto the rail and tighten the eccentric bushes until any vertical play is removed. Lightly try to move the assembly on the X axis, if there is any slop then it needs to be a little tighter but probably no more than an 1/8th of a turn. Once set you should still be able to spin the rollers by hand, but still feel a fair bit of resistance. Once set slide the assembly over the full length of the V rails to check fo any tight spots. If there are then you need to check that the two halves of the fail are fully mated!!! Remove pinion gear by slackening off grubscrews and sliding away. Good idea to mark up original position. Disconnect airpipe feeding popup cylinder and slide off rack mounting plate. Slacken all 20 caphead screws, they only need a half to full turn. Move the rails up as far as they will go and then tighten just the screws on each end, finger tight is enough. These rails come in two parts, ensure they are fully mated together or they will cause tight spots later on. Using the joiners square in the picture set to 47mm, use it to set height of the V rails when the bubble shows it is level. Check at each end and in the middle. Once level, tighten all screws and recheck level. If there is no adjustment between the mounting plate and the rack as shown in the first picture, then we need to introduce some. This is the most important step as it ensures all the parts are running parallel to eachother and not causing excessive force!!! Get your sharpies oot and mark where the rack and pinion mate!!! Slacken off the larger screws, one at either end of the rack until you have a 3mm gap at each end. This is easy when removed, but once refitted you will need a cut down allen key to fit in the gap to adjust. Back off the set screws if not already. Slide the assembly back on and mesh the pinion to the rack at one of the ends, it does not matter which, lightly tighten a grubscrew on pinion to ensure there is no backlash felt between the key and keyway. Using a combination of the set screws and adjustment screw, adjust until there is no play between rack and pinion. Then turn each of the small set screws back an 1/8th to 1/4 turn and fully tighten the adjustment screw. This introduces a very small amount of play that should hardly be felt, but is just enough to stop premature wear between the two. Remove the pinion, slide the rack to the other end and repeat the process. Recheck the first end in case it has moved slightly while doing the second. Set distance from beam to popup cylinder using measurements from another assembly, or if you were clever enough you took these before taking everything apart? I wasn't! If it needs adjusted then slacken off the two setting bolts, they give around 10mm on the mounting slots. 1mm either way is good enough and will not cause problems. Reconnect air pipes, make sure everything is locked off and tight, job done. Evidence of incorrect adjustment will be evidenced by components in the assemblies prematurely wearing and coming away from their fixings. <br/> Mechanical end stops should only ever be used as a fail safe in cases of sensors failing. These should be set so that the gears can never come off the racks. <br/> Using a pair of 13mm spanners, nip the proximity sensors in place so that they are roughly in the middle of the slot. <div class="icon-instructions caution-icon"> <div class="icon-instructions-icon"><i class="fa fa-exclamation-triangle"></i></div> <div class="icon-instructions-text">...Ensure that the black part of the sensor is close enough to the rack that it makes the sensor but not so close that it is likely to get damaged by contact</div> </div> Do this for all 6 sensors (2 on each assembly - 1 'home' and 1 'out') <div class="icon-instructions pin-icon"> <div class="icon-instructions-icon"><i class="fa fa-thumb-tack"></i></div> <div class="icon-instructions-text">...The 'Home' position for all cranks is when the pop ups are in the closest position to the machining centre - ready to receive the profile</div> </div><br/> It is also worthwhile slackening off all the screws that hold the air pipe harness, let it find its own position and then tighten back up. If not done this can introduce pull on the brackets that carry the Delrin rollers. The cranks can be run from the IO testing screen. The system will automatically stop the crank motor when the associated input is active, or after an adjustable timeout delay in the parameters. '''Machining centre side:''' Crank C - Machining centre offload '''Sawing Side:''' Crank D - Transfer Table Crank E - Saw Preload Ensure the 3 clutches are tensioned correctly. The purpose / goal of the clutch is to ensure that if a sensor fails, the motion of the rack is stopped safely on the end stop without damage or stress to the system '''Too Tight''': The clutch tension does not allow slippage causing the end stop to bend '''Too Loose:''' The clutch slips with a full table of profile Access V rails and adjust. Check and adjust Delrin rollers Adjust Rack to Pinion Misadjusted Other Checks End Stop Sensor Position Clutch Tension Testing 2024-02-23T09:50:33Z 2460363.9101042 ZX5 Transfer Table Setup 1 false true 1 0 0 1 plainlist 3 [[:Dokit:DocOptions]] [[DokitEPIEnable::yes]] ZX5 Transfer Table Setup# QUERYee7a61aae48f1c3f91d8e4d7736360be Torque Limiter Plates 844 fr Torque Limiter Plates Comment on 102 fr Comment on