]> 2026-04-28T02:33:31+02:00 ZX5 MH Infeed Basic IO Test and Setup 0 en Draft Guide for basic Input and Output testing / setup on the ZX5 MH Infeed Module Medium 4 hour(s) The MH infeed on a ZX5 is a module which can be tested individually away from the fully installed machine. Once build stage is complete, to be able to test individually, the Infeed Module needs: - To be connected to mains power & be powered on - An air supply to the main blue line - Network connection (Network Cube) - HDMI & Keyboard dongle to be plugged into the Beckhoff PLC inside the cabinet. Input and output activation when testing the sole module is done through the Twincat project rather than through WinMulti The above is only required If the Machine is not fully installed and connected with power air and network already. The below guide is specifically for a fully installed and connected infeed. false en ZX5_MH_Infeed_Basic_IO_Test_and_Setup_Full_infeed.jpg none Make sure the reset of the Estop circuit works. Be aware when resetting this will reset the air to home all pneumatics. Test each emergency stop button individually (Button box, infeed rear middle and end) making sure this breaks the circuit when pressed and the air is dumped. The Infeed beam sensor should be tested, when broken should also break the circuit and dump the air. Check on Service menu - IO tab that each input works correctly for each Estop unit. The home position of the roller beds should be up when the Estop circuit is ok and air is on. Open the Service menu - IO infeed tab and use the output Y157 OUA_Roller to activate, moving the roller beds to the down position under the infeed plastics. If they are moving the correct orientation, ensure all beds move up and down together, and arrive to position at the same speed or as close to as possible. Speeds should be roughly set when roller bed units are assembled. A rough setting is to wind each flow reg fitting completely in and then wind out 2 full turns. Some may need tweaking to even out the speeds across all tables. Home position for the loader is up on the rubber stop. home sensor Input X304 InA_WheelHm should be on (red) when the loader wheel is up in the home position. if it isn't the sensor on the cylinder needs to be adjusted. Activate the loader wheel down using Output Y154 OuA_WheelDo. When activated set the pressure gauge on the back of the infeed cabinet to around 1Bar. Adjust the flow reg fittings to set the speed of the wheel down and wheel home. See video for rough speed required. -Check Material load sensor is on the second set of rollers from the MH -Make sure sensor is mounted the correct orientation, see picture -Test sensor by covering and check to see if the input onscreen works ok (Sensor flashes with an orange light when activated , input flashes red on screen) -Check Mat Load blower output works and activates the blower. -Using the flow reg, whilst activated set the blower flow regulation to a speed where it doesn't activate the sensor. Lock off the flow reg with pliers Ensure chain sensor is mounted in the correct position to see the top part of the pegs, test by moving the chains by hand (with the clutch loosened) Check Input on screen is activating when the sensor is covered by a peg. Follow guide [[WEG Inverter Setup]] to set the correct parameters in on the Infeed chain / pegs and loader wheel inverters. Activate out for infeed chains to test directions forwards and backwards are correct. Clutch tightness needs to be set, it should not slip with a full table of heavy profile. During testing phase it can be tightened enough so thats a lot of force is needed to manually make the clutch slip. Firstly check the measurement from the centre of the loader wheel to the backfence is 32mm Test directions using the outputs on the IO tab Set clutch tightness using the following guide xxxxx Use the IO screen to make sure all buttons activate the correct Input -Set L/D and Distance on each sensor Using a Piece of Stuga Test Profile move the gasket side to be approx 120mm from each sensor. -use a small flat head screwdriver to turn the L-D dial, turn until the orange light comes on then slightly back off just enough for the orange light to turn off -Then use the same screwdriver on the range dial to set the distance to just turn both green and orange light on . '''Seperate guide ? is there already one?''' Emergency Stop and Reset Test Inverter set up Open Winmulti software from desktop Roller Bed Pneumatic test Infeed Loader Wheel Pneumatic test Material Load + Blower Set up Chain Sensor Offcut Sensor Set up Infeed Chain Pegs Test Loader Wheel set up Input Buttons test 2024-09-26T13:46:17Z 2460580.0738079 ZX5 MH Infeed Basic IO Test and Setup 0 false false 0 0 0 1 plainlist 3 [[:Dokit:DocOptions]] [[DokitEPIEnable::yes]] ZX5 MH Infeed Basic IO Test and Setup# QUERYee7a61aae48f1c3f91d8e4d7736360be