]> 2026-06-13T16:31:19+02:00 Toshiba - B-EX4T1 Printer Setup 0 en Draft B-EX4T1 Printer Setup for Auto Labeling Easy 20 minute(s) false en Toshiba_-_B-EX4T1_Printer_Setup_Toshiba_TEC_-_B-EX4T1_Series_-_1.jpg none To gain access turn the green knob to FREE. You can then pull the front plate down and lift the printer head up. The instructions for both the Inner & Outer wound labels are on the inside of the open lid. <br/> There will be no ribbon and as the settings will be for Peel Off a length of blank backing needs to be fed onto the Rewind spool Ensure the switch is set to REWINDER With the Printhead open ensure that the labels are under the small black sprung guides. Slide the green guide to the width of the label. Ensure that the sensor head is in the middle of the label When loaded close the Printhead down, lift the front plate up and turn the green knob to LABEL. For easy setup use a USB cable (Alternatively everything can be done via the network web interface) 1) Connect a USB cable to the PC 2) Connect a Network cable to a live DHCP network to obtain an IP address. 3) Download and install the BCP setup software: [https://url6.mailanyone.net/scanner?m=1pIYAE-0003U9-3G&d=4%7Cmail%2F90%2F1674147000%2F1pIYAE-0003U9-3G%7Cin6f%7C57e1b682%7C27359798%7C12301058%7C63C975823F8CF099951D682ADAAD7EC2&o=%2Fphtw%3A%2Fwtsbow.thiatsdcecwm%2Fo.ovanlr_oeodissetprna%2Fisergttn%2FeCo_t_%2FBPol%2FseireS&s=uO4_tHdOp9-EM4-X9--MGgLUV_Y https://www.toshibatec.com/download_overseas/printer/setting_tool/BCP_Series/] [https://url6.mailanyone.net/scanner?m=1pIYAE-0003U9-3G&d=4%7Cmail%2F90%2F1674147000%2F1pIYAE-0003U9-3G%7Cin6f%7C57e1b682%7C27359798%7C12301058%7C63C975823F8CF099951D682ADAAD7EC2&o=%2Fphtw%3A%2Fwtsbow.thiatsdcecwm%2Fo.ovanlr_oeodissetprna%2Fisergttn%2FeCo_t_%2FBPol%2FseireS&s=uO4_tHdOp9-EM4-X9--MGgLUV_Y] If the labels have been fitted properly on power up the calibration process will eject several labels. Take a note of the IP address given to the printer on the front panel. When you start BCP you should see as picture Select USB if not Selected 1) Pressing "Feed" should push out another label regardless. 2) Send a label to the printer via the network (or via the Test - Send file within BCP). 3) Send more than one file and make sure that each time you remove a label from the output the next one is presented. # Within BCP choose "Parameter Settings" # Select the LAN tab # Enable TCP/IP # Enable Wired LAN # Set IP Address and Sub Net Mask # Press the Set Parameter at the bottom. <br/> Press the Emulation Button and take the top option "Zmode System Parameter Settings" Then Make the changes *Label Length '''38mm''' (after calibration this will be reset to 41.3) *Label Width '''98mm''' *Ribbon '''WITHOUT RIBBON''' *Print mode '''PEEL OFF''' *Sensor '''TRANS PREPRINT''' *Max Label Length (for calibration) '''200mm''' (this just saves on labels) Press the '''DOWNLOAD''' button and check that there are no errors. Now on the Toshiba side: *Select Paraeter Settings *Select Standard 2 (General 2 on BCP TOOL) *Adjust Cut Adjust to -2.0 *Press the submit button The screen shows the Web version. The adjustment brings the label forward out of the printer to allow collection by the Picking Arm. <br/> <div class="icon-instructions info-icon"> <div class="icon-instructions-icon"><i class="fa fa-info-circle"></i></div> <div class="icon-instructions-text">...This is often necessary to make sure the printer returns in emulation mode properly</div> </div> Setting Rewinder Label Guides Sensor Position Closing Label Head Connecting printer to PC Initial Power up Rewind Spool Printhead access Using BCP to setup the printer Change Settings Set the IP Address for the Customers network Inner & Outer Testing Power printer off and On B-EX4T1 Toshiba 2023-03-22T14:53:17Z 2460026.1203357 Toshiba - B-EX4T1 Printer Setup 0 false false 0 0 0 1 plainlist 3 [[:Dokit:DocOptions]] [[DokitEPIEnable::yes]] Toshiba - B-EX4T1 Printer Setup# QUERYee7a61aae48f1c3f91d8e4d7736360be