]> 2026-05-26T21:42:19+02:00 TB0426 Replacement Zebra Printer Setup 0 en Draft This will describe the setup of a replacement Zebra printer after a fault with one on site. Medium 10 minute(s) <div class="icon-instructions caution-icon"> <div class="icon-instructions-icon"><i class="fa fa-exclamation-triangle"></i></div> <div class="icon-instructions-text">...This printer is now obsolete. The direct replacement is a ZD620 Click below for instructions on setting the replacement up</div> </div> [https://stuga.dokit.app/wiki/TB0452_ZD620_Zebra_Printer_Setup ZD620 Instructions] false en TB0426_Replacement_Zebra_Printer_Setup_0426_01.jpg none Open box, unwrap printer, plug in power and plug Ethernet connected to network to the printer. As the printer boots up there will be a red light displayed on the front. After around 30 seconds this will turn green as the printer completes boot up. Using the latches on the sides, open the printer and place in a label reel as shown in photo. Now ok to close the printer and front roller. Hold down the button until the green light flashes once, then release. This should printout 8 labels with various parameters on them, look for the label with ‘IP Address’ as shown in figure 2. Open any browser (Microsoft Edge, Chrome, Firefox) and type the IP address on the label into the search bar. IP addresses such as “192.168.016.079” should be typed as”192.168.16.79” This will now open the Zebra Printers home page. From here we can alter all settings required to set up a replacement printer. Click on ‘View and Modify Printer Settings’. When prompted for a password type: 1234. This will be the same password whenever prompted again. You will now be on the ‘View and Modify Printer Settings’ page. Now go to “General Setup”. From here you need to check parameters and change them if needs be. Darkness: 30 Print Mode: Peel off Speed: 3IPS Then save changes. Then go to “Calibration”. Power up: Calibration Head close: Feed Save. Using TeamViewer go onto the costumer’s machine’s computer where the printer is to be replaced. There are several ways of archiving this, the most reliable of which is finding the “params.saw” txt file. This will be in the C:\ drive. Open this and find “PrinterIPAddress”. This will be the most recent IP address for the printer on their current network. This ensures the printer only needs to be connected to the company’s network to operate. (If on an older system see notes) Go back onto the “Change and Modify Settings” menu on the printer interface. From here go to “Network Settings” and then to “TCP/IP Settings”. IP Address: (the IP address found in step 9) IP Protocol: PERMINANT. Submit changes and save in all menus. <nowiki>It is now recommended to re-print the parameters (like step 3) and stick the IP section of stickers on the bottom of the printer. Printer is now setup. <br /><br />Note: when saved you will not be able to alter again as the printer will have the company’s IP address. If alteration to parameters a Factory reset would be required. To do this hold down the green button and wait for the light to flash 4 times, then release. The printer will now be reset. Wait till green. Repeat this technical bulletin. <br /><br />For more information see the zebra GK420d online user guide: https://www.zebra.com/content/dam/zebra/manuals/printers/desktop/legacy/gk420d/gk420d-ug-en.pdf</nowiki> Neuron Old Systems. This applies if the machine has not been upgraded to a more recent system. Printer IP address will be found in an XML file, (Master > ZPL > files) under printer IP address. Boot up printer Place in label reel Printout 'IP Address' label Open browser and type in IP Address Open the homepage Check parameters Calibration TeamViewer Network Settings and IP Protocol Re-print parameters Notes TB0426 Zebra Printer Setup 2020-02-28T16:25:30Z 2458908.184375 TB0426 Replacement Zebra Printer Setup 0 false false 0 0 0 1 plainlist 3 [[:Dokit:DocOptions]] [[DokitEPIEnable::yes]] TB0426 Replacement Zebra Printer Setup# QUERYee7a61aae48f1c3f91d8e4d7736360be