]> 2026-05-26T12:17:20+02:00 R0015278 Mount Completed Assemblies Section two 0 en Draft Second page of instructions To complete R0015278 assembly mounting Medium 1 hour(s) '''<u>Tools Required</u>''' Standard Hex key set Standard spanner set 300 mm rule 1000mm rule '''<u>Parts Required</u>''' D0008288 Takeup Pad Left (D7339) (Wet/P F Matt) x 1 D0015583 Take Up Beam Joiner x 1 D0015598 Datum Flag: Saw Infeed x 1 D0015717 Energy Chain Angle Bracket Lower x 5 D0015718 Energy Chain Angle Bracket Upper x 2 D0015718B Energy Chain Angle Bracket Double Deck x 3 D0015720 Carriage Bracket x 1 D0015721 Energy Chain Tray Deep Long x 1 D0015723 Energy Chain Tray Shallow x 1 D0015724 Energy Chain Tray Deep x 2 D0015725 Energy Chain Tray Shallow Medium x 1 D0015742 Takeup Pad Right ZX5 x 1 D0015862 Energy Chain Tray Deep Long x 1 E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 1 R0015011 Bench Assemble Gripper R0015063 Bench Assemble Roller Tables R0015096 Bench Assemble Transfer Drive Assembly R0015101 Bench assembly take up assembly R0015286 Bench Assemble X axis components and energy chain false en R0015278_Mount_Completed_Assemblies_Screenshot_2023-08-16_111949.png none these steps follow on from dokit [[R0015278 Mount Completed Assemblies]] Use loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connections Pen mark all fasteners to show finalised Clean threads in parts D0015742 Takeup Pad Right ZX5 x 1 D0008288 Takeup Pad Left (D7339) (Wet/P F Matt) x 1 Mount remaining 3 take up arms as shown using fasteners stated in previous step Black take up pads D0008288 and D0015742 are not fitted at this point . These will be fitted at a later stage of build Use 4 off F0000299 M6 d nuts and 4 off M6 x 20 socket caps and M6 penny washers to mount takeup arm at position shown <div class="icon-instructions caution-icon"> <div class="icon-instructions-icon"><i class="fa fa-exclamation-triangle"></i></div> <div class="icon-instructions-text">...Ensure hard stop is fitted in correct orientation as strike post is offset on mounting plate. See picture for correct orientation</div> </div> 1 Over ride lock function so piston on cylinder can move freely 2 Mount cylinder in position shown . Do Not apply adhesive to these fasteners yet . use M6 x 20 socket caps and penny washers to secure cylinder assembly 3 Mount hard stop as shown using M6 x 20 socket caps and 20mm diameter washers at top position , Bottom position uses M6 x 20 socket caps and A form washers Please quality check finish on below channel bars . Paint work should match on both bars in regards to colour and finish (ie matt /gloss) Report any discrepancy to supervisor This is section two Unless otherwise stated Clean threads Mount 1st take up arm Mount 2nd,3rd and 4th arms Mount cylinder assembly and hard stop Note Quality check 2025-02-20T09:44:54Z 2460726.9061806 R0015278 Mount Completed Assemblies Section two 0 false false 0 0 0 1 plainlist 3 [[:Dokit:DocOptions]] [[DokitEPIEnable::yes]] R0015278 Mount Completed Assemblies Section two# QUERYee7a61aae48f1c3f91d8e4d7736360be