]> 2026-05-26T09:19:55+02:00 R0015087 Pneumatic Connections 0 en Draft Instructions to install pneumatic connections to main frame Medium 8

hour(s)

'''Tools require''' Pipe cutters Number identification Flush cutters '''Parts required''' P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 8 P0000160 Fitting: Flow Controller In Line 6mm x 2 P0000551 6mm inline Quick Exhaust Fitting x 7 P0001008 Regulator: ARG20 0 - 8.5 Bar c/w Gauge x1 P0001022 Regulator Bracket: to suit P0001008 x 1 A0000343 energy chain x 1 A0000344 energy chain bracket set x 1 D0015577 Fixed energy chain bracket x 1 P0001030 6mm compact tee x 12 false en R0015114_Bench_Assemble_Valve_Banks_and_Regulators_Screenshot_2023-11-02_074048.png none All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added Identification 2209 Connected to active port of valve bank (4) Connect 12mm blue airpipe from valve banks to end of frame for machine connections Valve bank connections are as follows Front row of valve bank (4) is the active ports, These will all be connected with suffix 9 pipe identifications Back row (2) is the home position , these will always be connected with suffix 1 pipe identifications Material blower should be identified as 2399 Located on roller assembly close to saw unit P0000160 flow reg required to control flow onto sensors, this should be pre fitted to roller assembly at bench assembly stage Connect to active port ln valve bank (4) Feed pipes from valve bank should be run to transfer arm location 4 Identifications will be 2319 2309 2299 Connect to active port on valve bank (4) Fit A000343 energy chain @40 links A0000344 energy chain brackets as shown Mount to D0015577 fixed bracket with M3 x 6 panhead screws and attach to support arm as shown using M4 x 16 socket caps, A form washers and M4 nyloc nuts . Must have a P0000551 Q.E.V fitted to each line Ensure 1.5 m of pipe is left exiting the end of the energy chain Use schematic for pneumatic connections Ensure P0000551 Q.E.V are fitted Identification 1479 Connects to active port on valve bank (4) Use P0001030 compact tee to connect Ensure enough loom to allow full range of movement Identification 1461 and 1469 Roller bed is lifted at home position Use P0001030 6mm tee for connections 1461 to home port on valve bank (2) 1469 to active port on valve bank (4) Identification 2419 Must have flow regulation P0000160 Split feed with P0001030 6mm tee Connect to active port (4) on valve bank Fit tie bases as shown to gripper support arms . Ecr raised to add holes to drawing 06/11/23 Fit P0001008 Regulator: ARG20 0 - 8.5 Bar c/w Gauge x1 P0001022 Regulator Bracket: to suit P0001008 x 1 to bracket shown Gripper height is lifted for home position identification 1311 Home port of valve bank (2) to nose of cylinder 1312 base of cylinder to out port on regulator Ensure P0000551 Q.E.V are fitted to both grip height cylinder ports 1319 In port of regulator to active port on valve bank (4) Install 1 off cable tie base as shown Run cable X44 and X10 as shown Leave loops of excess cable tied off ready for electrical termination Leave cable X283 tied off in a loop on cylinder It is vital that when installing pipes into the main X axis energy chain, that cable retaining points are used All cables and pipes should be secured with tie wraps to the 'fingers' on the energy chain brackets at BOTH ends Mount pre assembled pneumatic rail with 2 off M8 x 20 socket cps. Use 1 off M8 A Form washer on slotted end of rail Unless otherwise stated Y239 Material blower Y231, Y230 and Y299 Pop up feeds Y221 channel Y220 channel lock Y147 pop up E Y146 Roller Bed Y241 Rack blower Y131 Grip Height Connect ring main Valve Bank Connections Cable looms Important mount pneumatic rail 2024-03-11T13:48:15Z

2460381.0751736

R0015087 Pneumatic Connections 0 false false 0 0 0 1 plainlist 3 [[:Dokit:DocOptions]] [[DokitEPIEnable::yes]] R0015087 Pneumatic Connections# QUERYee7a61aae48f1c3f91d8e4d7736360be