]> 2026-05-26T08:19:33+02:00 R0015064 Bench Assemble Clamp Assembly Part 2 0 en Draft Details of bench assembly for saw clamps Medium 1 minute(s) '''<u>Tools Required</u>''' Standard hex key set Standard spanner set External circlip pliers 20mm bearing dolly Reduced shank 5mm hex key '''<u>Parts Required</u>''' B0000033 Linear Bearing: Ø20 x 30 Compact (Metal Case Only) x 8 B0000034 Linear Bearing: Ø16 x 30 Compact (Metal Case Only) x 8 B0000200 Circlip 8mm External x 12 B0000346 Ball Bearing 8 D 22 D 7 Long + seals x 6 D0004331 Clamp Head (D7450) x 1 D0004332 Clamp Mount Block (D7449) x 1 D0004333 Pillar x 2 D0004358 Clamp Head Bracket (D7447) x 1 D0004359 Clamp Head Cylinder Bar (D7446) x 2 D0004550 Clamp Insert x 2 D0004808 Slide Stop x 2 D0005191 Bearing Protective Washer x 4 D0005425 Clamp block Right (5625) x 1 D0005566 Clamp block left - Roller style (5567) x 1 D0005568 Clamp block left roller shaft x 3 D0007447 Clamp Head Bracket OH (D4358) x 1 D0007449 Clamp Mount Block OH (D4332) x 1 D0007450 Clamp Head OH (D4331) x 1 D0015266 Shaft 38.7mm: 440mm ZX Saw Top Clamp BZP x 2 D0015299 Shaft 16mm: 320mm Chip Deflector ZX5 x 1 D0015446B Chip Deflector Mounting Plate (Tapped) x 1 D0015447B Chip Deflector Probe Ø50 (Tapped) x 2 D0015454 Chip Deflector Rod (M16) x 2 H0004625 Shaft 16mm: 150 Saw Clamp x 2 H0004626 Shaft 16mm: 275 Eject Push x 1 H0004627 Shaft 20mm: 210 Saw Inner Clamp x 2 H0004628 Shaft 20mm: 245 Saw Outer clampx 2 M0001194 Kipp clamp handle x 2 P0000007 Straight Adaptor 6mm - 1/8 BSP tapered thread x 1 P0000054 Cylinder Ø32 x 50 (PIS32A50) x 1 P0000064 Pneumax microcylinder 25bore x 80stroke x 2 P0000295 Elbow Adaptor 6mm - 1/8 BSPT (Metal type) x 3 P0001143 cylinder 32 x 175mm stroke ISO x 1 false en R0015064_Bench_Assemble_Clamp_Assembly_Part_2_Screenshot_2023-11-16_111240.png none All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added Slide assemblies together as shown Tare care not to damage bearing seals Remove excess grease from shafts once installed Once fitted, check movement is free and consistent 1 Fit hard stop assembly to clamp head. Use 2 off M6 x 16 socket caps to fix ,only apply light tension to this bolt to allow adjustment 2 Fit cylinder to hard stop bracket and attached cylinder piston to mounting plate , do not apply adhesive on either 3 Contract cylinder and tension all fixing points Ensure clamp movement is smooth and consistent with all fasteners tight Once alignment is achieved, fasteners must be finalised 1 Remove cylinder 32mm locknut an pull cylinder back. This gives access to 2 off M6 socket caps to finalise individually 2 Refit 32mm locknut applying adhesive to thread and finalise 3 Retract cylinder thread and nut, apply adhesive and finalise Repeat for other clamp assembly 1 Attach large cylinder to infeed clamp assembly using 2 of M6 x 35 socket caps , apply adhesive but only light tension 2 Insert pre built roller clamp assembly. Take care to not damage bearing seals when fitting shaft ,Apply adhesive to cylinder thread and wind into clamp block 3 Ensure cylinder is contracted and tension M10 cylinder nut and 2 off m6 socket caps to set alignment. Check movement is even and no tight spots are evident at ends of cylinder stroke 4 Finalise all fasteners 5 Repeat for Eject clamp side using 2 off M6 x 30 socket caps to fix shorted cylinder 1 Assemble deflector probes as shown 2 Attach to infeed clamp assembly using Dry M8 x 20 kcp grubscrew 3 Adjust length of probes to be 1mm Above bottom of clamp block 4 Apply adhesive and lock off and finalise all M16 nuts 5 Remove assembly from clamps Unless otherwise stated Fit clamp heads to clamp mount blocks Fit cylinder and align Finalise cylinder Fit clamp blocks Assemble Deflector Probes 2023-11-16T11:46:26Z 2460264.9905787 R0015064 Bench Assemble Clamp Assembly Part 2 0 false false 0 0 0 1 plainlist 3 [[:Dokit:DocOptions]] [[DokitEPIEnable::yes]] R0015064 Bench Assemble Clamp Assembly Part 2# QUERYee7a61aae48f1c3f91d8e4d7736360be